Q-Logic Q-Forms Kick Panel Enclosures オーナーマニュアル
Remove Original Kick Panel/Threshold Plate
• Remove threshold plate by prying carefully upward along bottom edge.
• Pull kick panel away from bulkhead to release mounting clips.
• Tilt bottom front edge upward, slide panel rearward to clear hood release lever and pull
• Pull kick panel away from bulkhead to release mounting clips.
• Tilt bottom front edge upward, slide panel rearward to clear hood release lever and pull
kick panel/threshold plate out of vehicle.
Modify Original Kick Panel/Threshold Plate
• Separate kick panel and threshold plate portions of part by cutting squarely across panel
approximately 1.5 inches forward (toward kick panel) of mounting clip on threshold section.
NOTE: Always check the fit of the Q-forms into the vehicle before any cutting or modifications are done.
Preparing the Q-Forms for Speaker Installation
• Cut the speaker holes into the Q-Forms before installing them into the vehicle.
• Install the speakers into the Q-Forms after they have been installed into the
vehicle.
• Install speaker wiring and crossover network as per manufacturer’s
instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of
speaker mounting surface. A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and
into mounting surface. Be careful to center speakers in mounting surface to
allow clearance for grill shell.
• Install tweeters as per manufacturer’s instructions.
• Install the speakers into the Q-Forms after they have been installed into the
vehicle.
• Install speaker wiring and crossover network as per manufacturer’s
instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of
speaker mounting surface. A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and
into mounting surface. Be careful to center speakers in mounting surface to
allow clearance for grill shell.
• Install tweeters as per manufacturer’s instructions.
I
nstall New Q-Forms Kick Panels (Always predrill all mounting screw locaitons)
• Lay Q-forms kick panel in approximate location and connect speaker wiring.
• Install rubber welt to exposed metal edge extending vertically from
• Install rubber welt to exposed metal edge extending vertically from
bottom of windshield molding to front edge of threshold plate.
• Install panel into permanent position previously held by original kick
panel. Be sure front edge of panel fits tightly against rubber welt.
• Reinstall threshold plate by pushing original clips back into place. It
may be helpful to hold panel tightly against rubber welt while pushing
front clip into place.
• Install long screw and spacer through hole at rear of panel and drive
into inner bulkhead sheet metal. It may be helpful to predrill screw
pilot hole if installed without power tools.
• Install grill shells by pressing snugly into woofer cavity.
may be helpful to hold panel tightly against rubber welt while pushing
front clip into place.
• Install long screw and spacer through hole at rear of panel and drive
into inner bulkhead sheet metal. It may be helpful to predrill screw
pilot hole if installed without power tools.
• Install grill shells by pressing snugly into woofer cavity.
QL-K1005
GM Camaro/Firebird/TransAm 1993-1999
Estimated Installation Time: 1.5 Hrs.
9/10/98
QL-K1005 Included Hardware:
(1) 3" screw
(3) 1" screws
(1) 2.5" plastic spacer
(2) 18" rubber welt sections
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills
(3) 1" screws
(1) 2.5" plastic spacer
(2) 18" rubber welt sections
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills