Mackie DLM8 オーナーマニュアル
DLM8/12 P
o
w
er
ed Loudspe
ak
ers
10
DLM8/12 Powered Loudspeakers
DLM8/12 Loudspeaker: Rear Panel Features
1. Power Connection
This is a standard 3-prong IEC power connector.
Connect the detachable power cord (included in
the packaging with the loudspeaker) to the power
receptacle, and plug the other end of the power
cord into an AC outlet.
the packaging with the loudspeaker) to the power
receptacle, and plug the other end of the power
cord into an AC outlet.
Make sure that the AC power is matched to
the AC power indicated on the rear panel
(to the left of the IEC receptacle).
the AC power indicated on the rear panel
(to the left of the IEC receptacle).
Disconnecting the plug’s ground pin is
dangerous. Don’t do it!
dangerous. Don’t do it!
2. Power Switch
Press the top of this rocker switch inwards to turn on
the loudspeaker. The front panel power LED will glow
with happiness...or at least it will if the loudspeaker is
plugged into a suitable live AC mains supply.
with happiness...or at least it will if the loudspeaker is
plugged into a suitable live AC mains supply.
Press the bottom of this rocker switch inwards to turn
off the loudspeaker.
As a general guide, DLM loudspeakers should
be turned on last, after any mixer or other
signal source. As such, they should also be
be turned on last, after any mixer or other
signal source. As such, they should also be
turned off first. This will reduce the possibility of any
turn-on or turn-off thumps and other noises generated
by any upstream equipment from coming out of the
speakers.
turn-on or turn-off thumps and other noises generated
by any upstream equipment from coming out of the
speakers.
BASS +2
TREBLE +2
AUX
LEVEL
R
L
100 - 240V
50 - 60Hz 250W
POWER
Line
Mic
Ch 1
Mix
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR
THE U.S. AND ICES-003, FOR CANADA. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
REVISION
SERIAL NUMBER
WARNING:
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
1
THRU
2
TRS =
TRS = Line
XLR
2000W
2W
POWER
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
N'OUVREZ PAS LA COUVERTURE. N'EXPOSEZ
PAS CET ÉQUIPEMENT À LA PLUIE OU À L'HUMIDITÉ.
MEM
SYS
2
1
2000W Digital Loudspeaker
/
3. Fan Vents
Do not obstruct the ventilation openings
of the loudspeaker. Fans move air over the
heatsinks to cool down the power transistors.
of the loudspeaker. Fans move air over the
heatsinks to cool down the power transistors.
If these vents are restricted, then the loudspeaker may
overheat and shut down.
overheat and shut down.
4. Kickstand
The kickstand on the DLM loudspeaker works
similarly to a kickstand on a bicycle. Simply pull
the kickstand out until it locks in place. Now tilt the
loudspeaker back so it leans on the kickstand. At a 50˚
angle (and aimed at your ears, not your knees), the
kickstand is ideal for using the loudspeaker as a
monitor. Bicycles aren’t used as monitors, only as mains.
the kickstand out until it locks in place. Now tilt the
loudspeaker back so it leans on the kickstand. At a 50˚
angle (and aimed at your ears, not your knees), the
kickstand is ideal for using the loudspeaker as a
monitor. Bicycles aren’t used as monitors, only as mains.
Be careful not to unplug the unit when
engaging the kickstand...unless you’re into
that sort of thing.
engaging the kickstand...unless you’re into
that sort of thing.
1
5
6
11
12
15
14
13
16
10
9
17
8
7
2
3
4