Fujifilm FP-100C Silk 15200851 ユーザーズマニュアル
製品コード
15200851
– 2 –
FUJIFILM PRODUCT INFORMATION BULLETIN • FUJI INSTANT COLOR FILM New FP-100C / FP-100C SILK
•
After loading, make sure that the white tab is not
folded between the film pack and camera back, then
close and lock the rear cover.
folded between the film pack and camera back, then
close and lock the rear cover.
•
Pull out the black covering paper bringing with it the
first white tab, and the camera is ready to use.
first white tab, and the camera is ready to use.
•
For further exposure and handling precautions, refer
to the instructions supplied with the particular cam-
era.
to the instructions supplied with the particular cam-
era.
Development Times and Temperatures
•
This film is designed for use at temperatures be-
tween 10°C and 30°C (50°F and 95°F), but yields best
results at 25°C (77°F).
tween 10°C and 30°C (50°F and 95°F), but yields best
results at 25°C (77°F).
•
The table below provides the development times for
this film according to encountered temperatures.
For best results, be sure to observe the following de-
velopment times and temperatures after pulling out
the film sheet. Do not attempt to separate the nega-
tive and positive sheets before the temperature
specified times indicated below have elapsed.
this film according to encountered temperatures.
For best results, be sure to observe the following de-
velopment times and temperatures after pulling out
the film sheet. Do not attempt to separate the nega-
tive and positive sheets before the temperature
specified times indicated below have elapsed.
•
If development times are shorter or longer than
specified, undesired photos may result.
specified, undesired photos may result.
Development Procedures
•
Hold the white tab and pull it straight out bringing the
black tab through the film exit.
black tab through the film exit.
•
Hold the center portion of the black tab, and pull it out
at an even speed. Be sure to pull the black tab in a
direction within the film plane. If pulled in a slanting
direction, the white tab may break inside the film
pack. When pulling, do not bend, fold or press the
film and do not stop pulling before it is entirely
removed from the camera, or undesired results, such
as processing fluid leakage, incomplete processing
fluid spread or image unevenness may occur.
at an even speed. Be sure to pull the black tab in a
direction within the film plane. If pulled in a slanting
direction, the white tab may break inside the film
pack. When pulling, do not bend, fold or press the
film and do not stop pulling before it is entirely
removed from the camera, or undesired results, such
as processing fluid leakage, incomplete processing
fluid spread or image unevenness may occur.
•
When film has been removed from the camera, start
development time measurement immediately. Do not
rub, fold or separate developing films or undesired
spots may appear on finished photos.
development time measurement immediately. Do not
rub, fold or separate developing films or undesired
spots may appear on finished photos.
•
After the specified development time has lapsed,
separate the negative and positive sheets at a fixed
but rapid speed, starting with the black tab end.
separate the negative and positive sheets at a fixed
but rapid speed, starting with the black tab end.
•
The photo will be moist immediately upon separation.
Moist photos should not be placed on other photos
or paper lest they stick. When immediate use is
essential, dry photos using a dryer.
Moist photos should not be placed on other photos
or paper lest they stick. When immediate use is
essential, dry photos using a dryer.
•
If the white tab does not protrude from the camera,
open the camera rear cover in subdued light, pass
the white tab through the white tab exit and close rear
cover. The remaining films can be used as they are if
correctly set.
open the camera rear cover in subdued light, pass
the white tab through the white tab exit and close rear
cover. The remaining films can be used as they are if
correctly set.
•
If the black tab does not come out when the white tab
has been completely pulled out, open the camera
has been completely pulled out, open the camera
Temperature°C (°F) 35 (95) 30 (86) 25 (77) 20 (68) 15 (59) 10 (50)
Development Time (sec.) 60
Development Time (sec.) 60
75
90
120
180
270
rear cover in subdued light and pull the film out by the
black tab. (The film that is removed in this manner
cannot be used again, but the remainder can be
used.) If the development roller and film exit are
found to be dirty, clean them before closing the rear
cover.
black tab. (The film that is removed in this manner
cannot be used again, but the remainder can be
used.) If the development roller and film exit are
found to be dirty, clean them before closing the rear
cover.
4. FILM HANDLING PRECAUTIONS
CAUTION
•
Each film sheet contains a caustic (highly alkaline)
processing fluid. Never cut, tear or punch holes in
unused films. Avoid skin contact with this process-
ing fluid.
processing fluid. Never cut, tear or punch holes in
unused films. Avoid skin contact with this process-
ing fluid.
•
Peeled-apart negative sheets should be folded in-
ward upon themselves when discarded. When
discarding negative sheets and other waste mate-
rials, be sure to avoid contact with children, pet
animals, paper, clothes, furniture and other impor-
tant objects or materials.
ward upon themselves when discarded. When
discarding negative sheets and other waste mate-
rials, be sure to avoid contact with children, pet
animals, paper, clothes, furniture and other impor-
tant objects or materials.
•
Should you get some of this processing fluid on
your skin, flush it off immediately with lots of water.
If any of the fluid gets into your mouth or eyes,
flush the affected area immediately with lots of
water, then see your doctor.
your skin, flush it off immediately with lots of water.
If any of the fluid gets into your mouth or eyes,
flush the affected area immediately with lots of
water, then see your doctor.
•
Photographic properties may change with time. Be
sure to use the film before the expiration date on the
package.
sure to use the film before the expiration date on the
package.
•
Avoid opening a film pack or loading a camera under
direct sunlight. After opening the film, do not leave it
in a bright place. Load it into the camera as quickly
as possible.
direct sunlight. After opening the film, do not leave it
in a bright place. Load it into the camera as quickly
as possible.
•
When handling a film pack, do not put pressure on
the light-shielding cover sheet or within the slots on
the rear of the pack. This may cause a film-ejection
failure or unevenness in the photo.
the light-shielding cover sheet or within the slots on
the rear of the pack. This may cause a film-ejection
failure or unevenness in the photo.
•
Unprocessed film should be kept away from X-rays
used to inspect checked-in baggage, etc. at airport
terminals. Strong X-rays can cause fogging of
unprocessed film. It is recommended such film be
placed in your carry-on baggage whenever possible.
(Consult with airport personnel for details.)
used to inspect checked-in baggage, etc. at airport
terminals. Strong X-rays can cause fogging of
unprocessed film. It is recommended such film be
placed in your carry-on baggage whenever possible.
(Consult with airport personnel for details.)
•
Film fogging may occur in hospitals, factories, labo-
ratories and other locations using X-rays. Keep films
away from radiation sources.
ratories and other locations using X-rays. Keep films
away from radiation sources.