One World Technologies Inc. EL2200 ユーザーズマニュアル

10 - English

See Figures 6 - 7, pages ii and iii.
When the radio/charger is connected to a power supply 
and in the ON position, the LCD display will show the 
time, frequency, mode, and settings. 
NOTE: The illustrations of the LCD display shown in this 
manual are only examples of the frequencies you may see 
on your radio/charger and are not the exact frequencies 
that you may choose to listen to.

See Figures 6 - 7, pages ii and iii.
Use the menu navigation buttons to turn the radio/charger 
on and off, control the volume, change frequencies, toggle 
between modes and set the time.
TURNING THE RADIO/CHARGER ON AND OFF:
Press the 

ON/OFF button to turn the radio/charger ON 

and OFF. 
When the radio/charger is on and a battery pack is 
connected as the power supply, the [

 ] symbol will be 

shown in the LCD display. If the battery charge is low, a 
flashing low battery indicator will be displayed [

]. If 

the radio is connected to an AC power supply, the battery 
indicator will disappear.
ADJUSTING THE VOLUME:
When the radio/charger is turned ON, the unit will return 
to the last volume setting used.


To increase the volume, press the 

VOL + button. 



To decrease the volume, press the 

VOL - button.

SWITCHING MODES:
To switch modes, press the 

MODE button. The selected 

mode will be displayed above the frequency. Press the 
MODE button until the desired mode is selected. There 
are four modes:


FM mode



AM mode



AUX mode



BLUETOOTH

®

 mode

AM/FM TUNING:
Use the 

SCAN   and SCAN   buttons to manually tune 

to the desired radio frequency. The selected frequency is 
displayed on the LCD.


Press the 

SCAN   button to tune to a lower frequency 

and press the 

SCAN   button to tune to a higher 

frequency.

NOTE: Briefly press either button (not press and hold) 
to tune one frequency step at a time. Press and hold 
either button to quickly find the next frequency with 
clear reception.



To decrease interference or electrical noise, adjust the 
position of the antenna or move the radio/charger to a 
higher elevation. The antenna folds into the handle and 
out of the way when not in use.

STORING A PRESET IN MEMORY:
The memory feature saves up to 20 frequencies as 
presets in the radio’s memory. You can save up to ten (10) 
frequencies each for FM and AM modes.


Tune to the desired AM or FM frequency.



Press and hold the 

PRESET button until the word 

“MEMORY” and the preset position number flash on 
the screen.



Press the 

SCAN   or SCAN   button to choose a 

preset position number.

 

NOTE: There are ten (10) preset positions for FM and 
ten (10) for AM. Only one station can be saved in each 
preset position.



Press the 

PRESET button again to store the frequency.

To tune to presets (FM or AM mode):


Press and release the 

PRESET button to cycle through 

each preset position number and its associated 
frequency.

SETTING THE CLOCK:
The time appears on the LCD display when the radio/
charger is on.


Press and hold the 

CLK/DSPY button until the “hour” 

display blinks. 



Press the 

VOL + or VOL - button to select the hour. 

 

NOTE: Time is displayed in 12-hour format only. To 
select an hour that is after noon and before midnight, 
cycle the hours until “PM” appears in the display.



Press and release the 

CLK/DSPY button to lock in the 

hour setting. “Minutes” will begin to blink.



Press the 

VOL + or VOL - button to select the desired 

number. 



Press and release the 

CLK/DSPY button again to 

confirm the time. 

See Figure 8, page iii.


Press the 

MODE button until AUX mode is highlighted.



Connect one end of a 3.5 mm audio patch cord 
(maximum 8 in. long) to the device.



Connect the other end of the 3.5 mm patch cord to the 
auxiliary input jack.



The phone/MP3 player must be on and in play mode 
for sound to be heard through the speakers.