Bird Gard LLC 0045T ユーザーズマニュアル
PRIOR TO INSTALLATION
Your Bird Gard
®
Super
Pro Wireless kit includes
a Transmit unit with an
antenna, AC adapter and
battery cable; and one or
more four-speaker Receive
units with an antenna and
battery cable. Open the
Transmit unit by pressing
backward on the two latches
on the side of the box.
Prior to operation, plug
the power cable into the
power jack on the control
unit, then route the cable
down through the slotted
rubber grommet and through the opening in the lower
part of the enclosure, see
Fig. 1.
IMPORTANT NOTE: Be certain that the OFF - ON switch
is in the
OFF position and the volume control is set to the
minimum
(LOW) volume level (counterclockwise) while
plugging the power cord into the Transmit unit.
INSTALLATION
1) Use the mounting hardware (included) to mount the
Transmit unit box to a wall, post or other vertical
surface. The Transmit unit can be mounted to any
convenient location, including indoors. Even though
the unit will transmit through walls, the reception
distance is improved if the unit is mounted with a
clear line-of-sight to the Receive unit. The reception
distance is rated up to 1,000 feet (304 meters).
2) Screw the rubber antenna
(included) onto the antenna
mount located on top of the
Transmit unit, see Fig. 2.
3) Plug the power adapter into an
electrical outlet or attach the
battery clip assembly to a 12V battery. The other end
of the cable should already be plugged into the power
Digital Bird Repeller
the selected recordings in their number order, and
the Time Off Interval will be the shortest time period
within the selected range.
The Random Mode is recommended to keep
birds from adapting to a preset pattern of
sounds. To operate the unit in Random mode, set
Switch 5 in Mode Settings as follows:
Switch 5
Switch 5
Mode
ON
Random mode ON
OFF
Random mode OFF
NOTE: The unit will always play for approximately 48 seconds
independent of the number of sounds that are selected.
PROGRAMMING EXAMPLE
Recording Switches:
Results:
1, 3, 5 and 6 to “ON” position
Plays Sounds 1, 3, 5 & 6
Mode Switches:
1 = “OFF” position
]
Time Off Interval is set to
2 = “ON” position
Medium, every 1 to 4 minutes
3 = “ON” position
]
Operates during daylight
4 = “OFF” position hours only
5 = “ON” position
Sounds in random, non-sequential order
VOLUME CONTROL
The unit has a volume control dial on the front panel
of the Transmit unit. Turning the dial toward
LOW
will result in reduced sound output and rotating the
dial toward
HIGH will result in an increase in sound
output.
CAUTION: Take care when turning the dial since the unit may be in an
inactive state when the dial is rotated. It could then reactivate at a very high
level of sound which could be painful to your ears.
POWER SWITCH
The
ON - OFF power switch enables the unit to
operate. Slide the switch to the
ON position to start
the unit. If you turn the unit
OFF, be sure to leave
it off for about 30 seconds before turning it back on
to allow the electronics to properly reset.
TROUBLESHOOTING
PROBLEM
Unit is on, but
no sound is heard
Unit is on, but plays same
sound over and over,
regardless of settings
Unit is not operating
properly in the
DAY or NIGHT mode
Unit does not function
properly when connected
to a 12-Volt battery
• Check volume settings.
• Check time of operation settings.
• Check that at least one sound is
• Check time of operation settings.
• Check that at least one sound is
selected to play.
• Decrease the distance between
• Decrease the distance between
the Transmit control unit and the
Receive speaker unit to ensure
proper reception.
• Reset the unit by turning it off
for 30 seconds, then back on.
• Double check Mode switch
settings.
• Make sure photocell is not
obstructed.
• Make sure the photocell is not
affected by bright lights in either
the front or the back of the unit.
• Check battery condition.
• Turn power switch on unit to
• Turn power switch on unit to
the OFF position. Reconnect the
battery, wait 30 seconds, then
switch the unit back on.
SOLUTION
Bird Gard Super Pro Wireless Instructions #655-0063-00 (Rev. 06-12-09)
©2009 Bird Gard, LLC. All Rights Reserved. Bird Gard® is a patented trademark of Bird Gard, LLC.
EPA Establishment Number 075130-OR-001. FCC ID#: XGA-0045T
LIMITED WARRANTY
IF YOU ARE NOT COMPLETELY SATISFIED, CONTACT THE PLACE OF PURCHASE OR OUR
CUSTOMER SERVICE DEPARTMENT WITHIN ONE (1) YEAR OF YOUR DATE OF PURCHASE
FOR PROMPT AND COURTEOUS REPLACEMENT, REPAIR OR REFUND.
BIRD GARD LLC'S LIABILITY HEREUNDER SHALL BE LIMITED TO REFUNDING THE
PURCHASE PRICE PAID BY CUSTOMER OR REPLACING THE PRODUCT, IN BIRD GARD'S
SOLE DISCRETION, AND UNDER NO CIRCUMSTANCES SHALL BIRD GARD BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES, OF ANY NATURE WHATSOEVER,
ARISING FROM THE CUSTOMER'S USE OR OPERATION OF THE PRODUCT; PROVIDED,
HOWEVER, THAT THIS LIMITATION MAY BE LIMITED BY STATE LAW.
EXCEPT FOR THE EXPRESS ONE-YEAR LIMITED WARRANTY SPECIFICALLY DESCRIBED
HEREIN, BIRD GARD DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, RELATING
TO THE PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS; AND THE EXPRESS WARRANTIES
ARE IN LIEU OF ALL OBLIGATIONS OR LIABILITIES ON THE PART OF BIRD GARD ARISING
OUT OF OR IN CONNECTION WITH THE SALE, USE, OR OPERATION OF THE PRODUCT.
P.O. Box 1690 • 254 West Adams Avenue
Sisters, Oregon 97759 U.S.A.
Toll-Free: (888) 332-2328 • Fax: (541) 549-5286
Website: www.birdgard.com • Email: info@birdgard.com
Fig. 1
Slotted Rubber
Grommet
Changes or modifications not expressly approved by Bird Gard, LLC could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
Fig. 2