Allen & Heath Xone:464 XONE 464 ユーザーズマニュアル
製品コード
XONE 464
XONE:464 User Guide
19
Connecting the Headphones and Local Monitor
L
TIP = L
RING = R
RING = R
LOCAL MONITOR
R
LOCAL (BOOTH) MONITOR OUTPUTS A pair of 3 pole TRS jack sockets provide left
and right outputs from the console local monitor system. These are impedance balanced
and can be connected to balanced or unbalanced equipment as shown above. Nominal
operating level is –2dBu but gain is available to drive +4dBu if required. Independent
control is provided for the local and the headphones monitor systems. This output
typically feeds the DJ booth monitor with the music only mix, and Cue if required.
and right outputs from the console local monitor system. These are impedance balanced
and can be connected to balanced or unbalanced equipment as shown above. Nominal
operating level is –2dBu but gain is available to drive +4dBu if required. Independent
control is provided for the local and the headphones monitor systems. This output
typically feeds the DJ booth monitor with the music only mix, and Cue if required.
HEADPHONES 2 OUTPUT Two outputs are available for stereo headphones, one on
the front panel, the other on the rear panel. This is convenient for permanent installation
or when two headphones are required at the same time, for example presenter and guest
in a broadcast application. The same signal is available from both. Headphones are
available in many different styles, impedances and volume ratings. To get the best from
your system we recommend that you use high quality closed ear headphones in the
range 30 to 600 ohms. 8 Ohm headphones are not recommended.
the front panel, the other on the rear panel. This is convenient for permanent installation
or when two headphones are required at the same time, for example presenter and guest
in a broadcast application. The same signal is available from both. Headphones are
available in many different styles, impedances and volume ratings. To get the best from
your system we recommend that you use high quality closed ear headphones in the
range 30 to 600 ohms. 8 Ohm headphones are not recommended.
WARNING Some headphones are more sensitive than others and can
produce higher output levels. To avoid damage to your hearing start with the
PHONES level control at minimum and turn up only as much as is needed to
maintain comfortable listening level. Do not drive headphones at high listening
levels for long periods of time.
PHONES level control at minimum and turn up only as much as is needed to
maintain comfortable listening level. Do not drive headphones at high listening
levels for long periods of time.
User Connector Options
SYS-LINK OUT
(option)
(user connections)
REMOTE
SYS-LINK OUT
(option)
(user connections)
REMOTE
SYS-LINK OUTPUT The console is supplied with a blank plate fitted here. An optional
kit of parts is available to install a 25 pin D-connector and circuit card which provides all
console outputs on a single connector. This is convenient when connecting the
XONE:464 as an expander to another console. Use a standard 25 pin one-to-one
shielded cable to plug this output into any Allen & Heath console fitted with SYS-LINK
input. Alternatively wire a custom cable as required. SYS-LINK operates unbalanced at
–2dBu and is not intended for long cable runs. Note that SYS-LINK input is not available
on the
kit of parts is available to install a 25 pin D-connector and circuit card which provides all
console outputs on a single connector. This is convenient when connecting the
XONE:464 as an expander to another console. Use a standard 25 pin one-to-one
shielded cable to plug this output into any Allen & Heath console fitted with SYS-LINK
input. Alternatively wire a custom cable as required. SYS-LINK operates unbalanced at
–2dBu and is not intended for long cable runs. Note that SYS-LINK input is not available
on the
XONE:464. Contact your Allen & Heath agent for further details.
USER CONNECTOR The console is supplied with a blank plate fitted here. A 25 pin D-
connector may be installed and custom wired to satisfy the particular requirements of the
application. The installation of this connector should be carried out only by qualified
personnel. Contact your agent for further details.
connector may be installed and custom wired to satisfy the particular requirements of the
application. The installation of this connector should be carried out only by qualified
personnel. Contact your agent for further details.