CommScope Inc. of North Carolina AIRBRIDGE-AP ユーザーズマニュアル
25
5.0 Remote Access
5.1 Description
Remote access of the AP is available through Telnet and SNMPv1. TFTP is available for remote
firmware upgrades.
firmware upgrades.
5.2 Supported Network Protocols
The AP Ethernet interface uses several TCP/IP protocols for network communication. The supported
standards are ARP, UDP, TCP, ICMP, Telnet, TFTP and SNMP. The electrical interface is fully compliant
with IEEE 802.3 10-Base-T Ethernet and
standards are ARP, UDP, TCP, ICMP, Telnet, TFTP and SNMP. The electrical interface is fully compliant
with IEEE 802.3 10-Base-T Ethernet and
100BASE-TX (auto-sensing)
.
5.3 Network Hardware Address
The hardware address of the AP Ethernet interface is printed on a label on the unit. This address is
unique for each unit and consists of 6 two digit hexadecimal values. The hardware address can also
be obtained via the interface (See Section 4.6.6). An example address is: 00:20:4A:52:3A:34
unique for each unit and consists of 6 two digit hexadecimal values. The hardware address can also
be obtained via the interface (See Section 4.6.6). An example address is: 00:20:4A:52:3A:34
5.4 Assigning an IP Address
The unit's IP address must be configured before a network connection is available. You have the
following options for assigning an IP to the unit:
1) Local Interface
2) DHCP
3) ARP and Telnet
LOCAL INTERFACE
The unit's Ethernet IP address, netmask, and gateway IP address can be assigned via the local interface,
refer to section 4.6.6 for further information on configuring available Ethernet parameters.
DHCP
The unit ships with a default IP address of 0.0.0.0, which automatically enables DHCP. Provided a DHCP
server exists on the network, it will provide the unit with an IP address, gateway address, and subnet
mask when the unit boots up or the Ethernet interface is renewed (See Section 4.6.6 for enabling DHCP
mode and renewing the Ethernet interface).
ARP AND TELNET
The following procedure sets a temporary IP address so that setup over the network can be
done:
a) Set a static ARP route with the desired IP address using the hardware address of the AP
Ethernet interface, which is printed on a label on the module. In Windows, a static route can be
set from the DOS prompt using the ARP command. The following example command sets a
default route to the IP address 10.10.10.11 via hardware address 00-20-4A-52-3A-34:
following options for assigning an IP to the unit:
1) Local Interface
2) DHCP
3) ARP and Telnet
LOCAL INTERFACE
The unit's Ethernet IP address, netmask, and gateway IP address can be assigned via the local interface,
refer to section 4.6.6 for further information on configuring available Ethernet parameters.
DHCP
The unit ships with a default IP address of 0.0.0.0, which automatically enables DHCP. Provided a DHCP
server exists on the network, it will provide the unit with an IP address, gateway address, and subnet
mask when the unit boots up or the Ethernet interface is renewed (See Section 4.6.6 for enabling DHCP
mode and renewing the Ethernet interface).
ARP AND TELNET
The following procedure sets a temporary IP address so that setup over the network can be
done:
a) Set a static ARP route with the desired IP address using the hardware address of the AP
Ethernet interface, which is printed on a label on the module. In Windows, a static route can be
set from the DOS prompt using the ARP command. The following example command sets a
default route to the IP address 10.10.10.11 via hardware address 00-20-4A-52-3A-34:
arp -s 10.10.10.11 00-20-4A-52-3A-34
-The IP address 10.10.10.11 is used here as an example only. This address must be replaced by
one that is valid for the target network in order for this procedure to function properly. The IP address
assigned must be on the same subnet as the computer doing the initial configuration. A network
administrator can supply the proper values for these parameters. Refer to Appendix C, IP Addresses,
Netmask, etc. for more information on IP address selection.
assigned must be on the same subnet as the computer doing the initial configuration. A network
administrator can supply the proper values for these parameters. Refer to Appendix C, IP Addresses,
Netmask, etc. for more information on IP address selection.
-In order for the ARP command to work in Windows, the ARP table on the PC must have at least
one IP address defined other than its own. Type “arp –a” at the DOS command prompt to verify that
there is at least one entry in the ARP table. If there is no other entry besides the local machine, ping
another IP machine on your network to build the table. This has to be a host other than the machine on
there is at least one entry in the ARP table. If there is no other entry besides the local machine, ping
another IP machine on your network to build the table. This has to be a host other than the machine on