Genex Telecom Co. Ltd. FRS300 ユーザーズマニュアル
ROGERS LABS, INC.
Genex Electronics
4405 W. 259th Terrace
MODEL: FRS 300
Louisburg, KS 66053
Test #: 010419
Phone/Fax: (913) 837-3214
Test to: FCC Parts 2 and 95
Page 1 of 2
FRS300Manual.doc 05/09/2001
FRS 300 Owners Operator Manual
Turning the Unit ON
Press and hold the power button. The unit will beep and the LCD display will briefly display a self-test screen.
Press and hold the power button. The unit will beep and the LCD display will briefly display a self-test screen.
Turning the Unit OFF
Press and hold the power button. The unit will beep and the LCD display will turn blank.
Press and hold the power button. The unit will beep and the LCD display will turn blank.
Adjusting the Speaker Volume
•
Press the UP (<) button to increase volume.
•
Press the DOWN (>) button to decrease volume.
•
The LCD displays volume level on lower right corner by the number of bars.
Receiving a Signal
The unit is continuously in the RECEIVE mode when the unit is ON. When you receive a Signal on the current
channel, the TX/RX LED lights up in green
The unit is continuously in the RECEIVE mode when the unit is ON. When you receive a Signal on the current
channel, the TX/RX LED lights up in green
Transmitting a Signal
1. Push and hold the PTT button to transmit. The TX will light up in red.
2. While holding the PTT button, speak in a normal voice about 2 to 3 inches away from the microphone.
3. Release the PTT button when you have finished transmitting.
1. Push and hold the PTT button to transmit. The TX will light up in red.
2. While holding the PTT button, speak in a normal voice about 2 to 3 inches away from the microphone.
3. Release the PTT button when you have finished transmitting.
NOTE: In order for other people to receive your transmission, they must be on the same channel you are currently
using. Refer to the “Changing Channels” section for more information.
using. Refer to the “Changing Channels” section for more information.
Changing Channels
This communicator has 14 available channels. To change channels:
1. Press and hold the MENU button until the channel number digit flashes on the LCD display.
2. While the channel number is flashing:
This communicator has 14 available channels. To change channels:
1. Press and hold the MENU button until the channel number digit flashes on the LCD display.
2. While the channel number is flashing:
•
Press the UP (<) button for a higher channel.
•
Press the DOWN (>) button for a lower channel.
•
The channel changes from 1 to 14, or from 14 to 1, repeatedly.
3. Press the MENU button or PTT button to select the desired channel and return to normal mode.
Monitor
You can use the MONITOR feature to check for weak signals in the current channel.
You can use the MONITOR feature to check for weak signals in the current channel.
•
Press and hold the MONITOR button until it beeps. MONITOR works continuously until released – pressed
MONITOR again.
•
Press the MONITOR button for channel skipping during SCAN mode.
LAMP+ (LAMP / KEY LOCK)
•
Press and release the LAMP+ key to light up the LCD display. The backlight will automatically shut off after 4
seconds when no key operation is made.
•
Press and hold the LAMP+ key until the KEY LOCK symbol is displayed. Volume and channel change is disabled
during KEY LOCK mode. Press the LAMP+ key the same manner again to release KEY LOCK mode.
CHANNEL SCAN
The SCAN activity works in an endless channel loop from 1 to 14.
1. Press the MENU button until Channel number digit flashes. Press the SCAN button to activate channel scan. The
channel number on LCD changes rapidly until an active signal is detected.
2. When an active signal (one of the 14 channels) is detected, SCAN pauses keeping the active signal broadcast.
Press PTT if you wish to communicate through the active signal channel. Then SCAN is stopped at the active
channel. But if communication is not desired, press UP/DOWN button to continue searching.
The SCAN activity works in an endless channel loop from 1 to 14.
1. Press the MENU button until Channel number digit flashes. Press the SCAN button to activate channel scan. The
channel number on LCD changes rapidly until an active signal is detected.
2. When an active signal (one of the 14 channels) is detected, SCAN pauses keeping the active signal broadcast.
Press PTT if you wish to communicate through the active signal channel. Then SCAN is stopped at the active
channel. But if communication is not desired, press UP/DOWN button to continue searching.