Dorman Products Inc. DORM30 ユーザーズマニュアル
ALL KEY FOBS MUST BE PRESENT AND REPROGRAMMED WHEN PROGRAMMING NEW FOBS
Programming Instructions:
1) Turn the ignition to ON (II).
2) Within 5 seconds press the LOCK or UNLOCK button on one of the remotes. (any programmed remote can be used for this
step).
3) Within 5 seconds turn the ignition switch to LOCK (0) position.
4) Within 4 seconds turn the ignition switch to ON (II).
5) Repeat steps 2,3 and 4 two more times using the same keyless remote used in step 2.
6) Within 5 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm
you are in programming mode.
7) Within 10 seconds press the LOCK or UNLOCK button on same remote.
8) Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks
cycle after you push each remote button to confirm system has accepted the remote.
9) Turn the ignition switch to LOCK (0) to exit programming mode.
10) Test remote (s).
2) Within 5 seconds press the LOCK or UNLOCK button on one of the remotes. (any programmed remote can be used for this
step).
3) Within 5 seconds turn the ignition switch to LOCK (0) position.
4) Within 4 seconds turn the ignition switch to ON (II).
5) Repeat steps 2,3 and 4 two more times using the same keyless remote used in step 2.
6) Within 5 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm
you are in programming mode.
7) Within 10 seconds press the LOCK or UNLOCK button on same remote.
8) Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks
cycle after you push each remote button to confirm system has accepted the remote.
9) Turn the ignition switch to LOCK (0) to exit programming mode.
10) Test remote (s).
FCC WARNING
Statement 15.19(a)(3):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. Changes or modifications not expressly approved by Dorman Products Inc. could void the user’s authority to operate the equipment.
operation. Changes or modifications not expressly approved by Dorman Products Inc. could void the user’s authority to operate the equipment.
FCC Part 15.21: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
IC WARNING
FVIN 63999373IC
The term IC before the Certification/Registration number only signifies that the Industry Canada technical specifications were met. This device
complies with Industry Canada’s license-exempt
The term IC before the Certification/Registration number only signifies that the Industry Canada technical specifications were met. This device
complies with Industry Canada’s license-exempt
RSSs
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference including interference that may cause undesired operation of the
device.
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.