Gecko Electronics Inc. RFMT1C ユーザーズマニュアル

 
 

 

 

 

 

 

 

 

To install the Interface Module, the 
following is required: 
 
1.  Disconnect the Main Power going 

into the spa. 

2.  Remove the equipment 

compartment door of the spa. 

3.  Attach the Module to the spa using 

the two (2) existing screws on the 
Interface Module label attached to 
the spa wall inside the equipment 
compartment).

 

4.  Open the IQ2020 Control Box  by 

removing the two (2) front screws 
and front cover. 

5.  Attached cable to the low voltage 

connector as illustrated below. 

 
6.  Close IQ2020 Control Box  by 

attaching cover and fastening using 
the two (2) screws. 

7.  Replace equipment compartment 

door onto spa. 

8.  Connect Main Power to spa. 

 

Starting the FreePad for the first time 
requires one (1) step: 
1.  Installing the batteries into the 

FreePad. 

The FreePad uses three AA alkaline 
batteries supplied with this packet. 
Insert a quarter into the slot inside the 
plug at the bottom of the FreePad,  rotate 
counter clockwise to open. Install the 
batteries with the positive (+) end 
towards the top of the FreePad and the 
negative (-) end towards the bottom. 
Once the batteries are installed, replace 
the plug and tighten with a quarter.  
NOTE: It is recommended that all three 
batteries be replaced at the same time. 

The Freepad comes pre-synchronized to 
the Interface Module.  Since the IQ2020 
will communicate with up to eight (8) 
FreePad controllers, any additional 
controllers will need to be manually 
synchronized.  The following is required 
to synchronize a FreePad controller with 
the Interface Module: 

1.  Press and hold both the Light Plus 

and the Light Minus buttons on the 
spa’s Main control panel 
simultaneously for two (2) seconds 
to initiate synchronization.  

 

 

2.  Press any FreePad button to wake 

the FreePad.  When the display 
illuminates, press the Plus button on 
the FreePad to complete the process.  

1.  Press and hold the Tiger Key for 

two (2) seconds on the spa’s Main 
control panel to initiate 
synchronization. 

2.  Press any FreePad button to wake 

the FreePad.  When the display 
illuminates, press the Plus button on 
the FreePad to complete the process. 

ƒ  Press any button on the FreePad to 

illuminate the FreePad screen.  

ƒ  Press the MODE button  to scroll 

throught the different screens. 

ƒ  Press the Plus (+) or Minus (-) 

buttons to activate or deactivate the 
function illustrated on the screen. 

ƒ  See Control Screens section for 

more information. 

 

The illustration below shows the screen 
elements and layout for the FreePad 
LCD Display. You may notice that some 
of these icons may not be present on 
your screen; this is because your spa is 
currently not equiped with that feature. 
 
 

Once the batteries are installed, the 
FreePad will always be in one of the 
following modes: 
1.  Communication Mode: In this 

mode, the FreePad is searching for 
communication with the IQ2020. 
The Comm Icon will flash. 

2.  Default Screen Mode: Upon power-

up from the Shutdown Mode, the 
FreePad shall display the following 
screen elements: 
•  READY Icon 
•  POWER Icon 
•  Current SET TEMP Icon 
Other Icons will only be displayed if 
the feature is installed and currently 
active. 

3.  Control Mode: By pressing the 

MODE button after viewing the 
Default Screen, you will be able to 
scroll through the available control 
screens. 

4.  Sleep Mode: 10 seconds after any 

button is pressed, the display will go 
blank,  placing the FreePad into a 
sleep mode. The sleep mode will 
continue for 30 minutes unless a 
button is pressed which would  start 
the entire cycle over again. 

5.  Shutdown Mode: After 30 minutes 

of non-operation by the user, the 
FreePad will revert to the shutdown 
be display when a FreePad button is 
pressed. 

 
 

  

 

 
 

 
 
 

 

2 

3