Wilson Electronics LLC 273201 ユーザーズマニュアル
Part # AIG 110727 - REV .28 - 04 .09 .12
Signal Booster Specifications
Dual Band Specifications
Model Number
Part Number
273201
Connectors
FME-Male
Impedance (input/output)
50 ohms
Dimensions
5 .6 x 3 .6 x 1 .7 inch (14 .2 x 9 .1 x 4 .4 cm)
Weight
1 .2 lbs (0 .54 kg)
Frequency
824-894 MHz / 1850-1990 MHz
1
Passband Gain (nominal)
800 MHz
Typical / Maximum
1900 MHz
Typical / Maximum
49 dB / 54 dB
50 dB / 55 dB
2
20 dB Bandwidth (nominal)
800 MHz
Typical / Maximum
1900 MHz
Typical / Maximum
25 MHz / 28 MHz
61 MHz / 67 MHz
Power output for single cell phone (uplink) dBm
800 MHz
1900 MHz
CDMA
30 .2
30 .7
HSPA
26 .8
28 .2
LTE
28 .2
28 .5
GSM
27 .8
29 .9
EDGE
27 .7
29 .8
3,4
Power output (uplink) for multiple
cell phones. dBm
The maximum power is reduced by
the number of channels:
Number of
cell phones
Maximum Power
800 MHz
1900 MHz
2
26 .0
22 .2
3
22 .5
18 .7
4
20 .0
16 .2
5
18 .1
14 .3
6
16 .5
12 .7
Power output for single received channel
(downlink) dBm
800 MHz
1900 MHz
CDMA
9 .3
7 .3
HSPA
8 .2
6 .1
LTE
8 .4
8 .3
GSM
9 .6
6 .6
EDGE
8 .5
6 .2
3,4
Power output for multiple
received channels (downlink). dBm
The maximum power is reduced by
the number of channels:
Number of
channels
Maximum Power
800 MHz
1900 MHz
2
6 .2
4 .6
3
2 .7
1 .1
4
0 .2
-1 .4
5
-1 .7
-3 .3
6
-3 .3
-4 .9
Noise Figure (typical)
3 dB nominal
Isolation
> 65 dB
Power Requirements
Signal Booster Usage
Signal Booster Usage
6 V, 0 .5 A - 2 A (subject to uplink power)
Notes:
1 . Nominal gain is the maximum gain at any frequency in the passband .
2 . Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB
lower than the passband amplification . One of the frequencies is lower than the passband and the other is higher .
3 . The Manufacturer’s rated output power of this equipment is for single carrier operation . For situations when multiple carrier
signals are present, the rating would have to be reduced by 3 .5 dB, especially where the output signal is re-radiated and can
cause interference to adjacent band users . This power reduction is to be by means of input power or gain reduction and not by
an attenuator at the output of the device .
4 . The maximum power for 2 or more simultaneous signals will be reduced by 6 dB for each doubling of the number of signals .
3301 East Deseret Drive, St . George, UT 84790
For additional Technical Support visit
www .WilsonElectronics .com
Phone: 866-294-1660 Fax: 435-656-2432