Wilson Electronics LLC 2B2725 ユーザーズマニュアル
7
#110856_Sleek4G-C_REV07_09.11.12
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: tech@wilsonelectronics.com
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
Signal Booster Specifications
Sleek 4G-C
Model Number
2B2725
Connectors
SMA Female
Impedance (input/output)
50 ohms
Frequency
1710-1755 MHz & 2110-2155 MHz / 824-894 MHz / 1850-1990 MHz
1
Passband Gain (nominal)
1700 / 2100 MHz
Typical / Maximum
800 MHz
Typical / Maximum
1900 MHz
Typical / Maximum
Uplink
19 dB / 21 dB
21 dB / 23 dB
20 dB / 23 dB
Downlink
21 dB / 23 dB
19 dB / 22 dB
21 dB / 24 dB
2
20 dB Bandwidth (nominal)
1700 / 2100 MHz
800 MHz
1900 MHz
46 MHz / 50 MHz
26 MHz / 28 MHz
61 MHz / 67 MHz
Power output for single cell phone
(uplink) dBm
1700 / 2100 MHz
800 MHz
1900 MHz
CDMA
26.5
29.2
28.2
EVDO
26.3
29.1
28.1
HSPA
23.2
28.4
26.2
LTE
23.6
27.7
26.8
GSM
26.3
29.1
28.6
EDGE
26.1
28.8
28.1
Power output for single cell phone (dowlink)
dBm
1700 / 2100 MHz
800 MHz
1900 MHz
CDMA
-9.1
-9.7
-7.0
EVDO
-8.6
-9.6
-7.8
HSPA
-6.4
-9.5
-9.0
LTE
-7.4
-9.8
-8.8
GSM
-9.3
-9.2
-9.3
EDGE
-8.7
-9.2
-9.5
3,4
Power output for multiple
received signals (uplink) dBm
The maximum power is reduced by
the number of signals:
Number of
signals
Maximum Power
3
1700 / 2100 MHz
800 MHz
1900 MHz
2
24.2
25.1
21.1
3
20.6
21.6
17.6
4
18.1
13.1
15.1
5
16.2
17.2
13.2
6
14.6
15.6
11.6
3,4
Power output for multiple
received signals (downlink) dBm
The maximum power is reduced by
the number of signals:
Number of
signals
Maximum Power
3
1700 / 2100 MHz
800 MHz
1900 MHz
2
-12.1
-10.4
-10.4
3
-15.6
-13.9
-13.9
4
-18.1
-16.4
-16.4
5
-20.1
-18.3
-18.3
6
-21.6
-19.9
-19.9
Noise Figure (nominal)
3 dB nominal
Isolation
> 40 dB
Power Requirements
5.5V DC, 1A
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband amplification. One
of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be
reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input
power or gain reduction and not by an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.