Wilson Electronics LLC 2B5125 ユーザーズマニュアル
110807_Sleek English_REV .09_12 .20 .11
Signal Booster Specifications
Sleek 4G-V
Model Number
2B5125
Connectors
SMA
Impedance (input/output)
50 ohms
Frequency
746-787 MHz / 824-894 MHz / 1850-1990 MHz
1
Passband Gain (nominal)
19 dB (typical) / 23 dB (maximum)
2
20 dB Bandwidth (nominal)
Uplink
Typical / Maximum
Downlink
Typical / Maximum
700 MHz
N/A
N/A
800 MHz
25 MHz / 28 MHz
28 MHz / 31 MHz
1900 MHz
61 MHz / 67 MHZ
61 MHz / 67 MHz
Power output for single cell phone
(uplink) dBm
700 MHz
800 MHz
1900 MHz
CDMA
N/A
29 .3
27 .8
GSM
N/A
28 .1
28 .3
EDGE
N/A
27 .5
27 .0
WCDMA
N/A
26 .9
27 .5
LTE
26 .5
28 .4
27 .5
Power output for single cell phone (dowlink)
dBm
700 MHz
800 MHz
1900 MHz
CDMA
N/A
-0 .1
-1 .3
GSM
N/A
-0 .5
-1 .3
EDGE
N/A
-2 .0
-1 .6
WCDMA
N/A
-2 .0
-4 .2
LTE
-2 .0
-2 .3
-4 .1
3,4
Power output for multiple
received channels (uplink) dBm
The maximum power is reduced by
the number of channels:
Number of
channels
Maximum Power
3
800 MHz
1900 MHz
2
22 .5
17 .9
3
19 .0
14 .3
4
16 .5
11 .8
5
14 .6
9 .9
6
13 .0
8 .3
3,4
Power output for multiple
received channels (downlink) dBm
The maximum power is reduced by
the number of channels:
Number of
channels
Maximum Power
3
800 MHz
1900 MHz
2
-2 .4
-4 .7
3
-5 .9
-8 .2
4
-8 .4
-10 .7
5
-10 .4
-12 .7
6
-11 .9
-14 .3
Noise Figure (typical)
3 dB nominal
Isolation
> 40 dB
Power Requirements
5V DC, 1A
Notes:
1 . Nominal gain is the maximum gain at any frequency in the passband .
2 . Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the
amplification is 20 dB lower than the passband amplification. One of the frequencies is lower than the passband
and the other is higher .
3 . The Manufacturer’s rated output power of this equipment is for single carrier operation . For situations when
multiple carrier signals are present, the rating would have to be reduced by 3 .5 dB, especially where the output
signal is re-radiated and can cause interference to adjacent band users . This power reduction is to be by means
of input power or gain reduction and not by an attenuator at the output of the device .
4 . The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals
is doubled .
3301 East Deseret Drive, St . George, UT 84790
For additional Technical Support visit www .WilsonElectronics .com
or email at: tech@wilsonelectronics .com
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www .twitter .com/WilsonCellular www .facebook .com/WilsonCellular