Wilson Electronics LLC 8011SB ユーザーズマニュアル

6

7

6.1  3 dB Splitter (Part# 859901)

6.2  6 dB Tap (Part# 859906) & 10 dB Tap (Part# 859907)

6.3  Coax Cable Extensions 50Ω (see chart on next page)

6.4  Antenna Options:

301103 - Magnet Mount, 5 dBi   

301111 - Yagi, 13 dBi

301106 - Low Profile, 2.2 dBi

301113 - Mini Magnet, 2.12 dBi

301121 - Dome, 2.5 dBi

301122 - Panel, 7 dBi

6.5  N-Male to FME-Male adapter (Part# 971113) 

Adapts 9913 Coax to fit the Amplifier

6.6  Lightning Surge Protection (Part# 859903)

 Lightning protection  is recommended for all installations.

If you need further assistance with your installation:

1)  Call us Toll-Free at 866-294-1660 (8:00 AM – 4:30 PM Mountain Time)

2)  E-mail tech support at tech@wilsonelectronics.com

3)  Go to 

  The outside antenna used with this amplifier must be fixed-mounted on an out-

door permanent structure with a separation of at least 20 feet from all persons 

during normal operation.

The inside antenna used with this amplifier must have a separation distance 

from all persons that is at least:

 

 

9 inches for the 2.5 dBi Dome antenna.

 

 

14 inches for the 7 dBi Panel antenna. 

The amplifier must not be co-located or operating in conjunction with any 

other antenna or amplifier.

Verify that both the Outside and Inside Antennas are connected before plug-

ging in the AC-DC power supply to the power outlet.

Lightning protection is recommended for all installations. 

Lightning protection is required for warranty validation.

951110

2’ Extension Cable RG58U 

Low Loss Coax

(N-Male to FME Female)

Used with the Yagi antenna to help find the 

optimum signal strength (for installation purposes 

only).

951101

5’ Extension Cable RG58U

Low Loss Coax

(0.6 db loss)

951102

10’ Extension Cable RG58U

Low Loss Coax

(1.2 db loss)

951103

15’ Extension Cable RG58U

Low Loss Coax

(1.8 db loss)

951104

20’ Extension Cable RG58U

Low Loss Coax

(2.4 db loss) N-Male to FME Female

951113

2’ Extension Cable 9913 Equivalent 

Ultra Low Loss Coax

(0.08 db loss) Jumper Coax - Can be used to con-

nect a splitter behind an amplifier.

951108

20’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax

Only use 9913 Equivalent Low Loss Coax for 

extensions 20’ or longer (0.8 db loss)

951105

30’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax

(1.2 db loss)

951106

50’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax

(2.0 db loss)

951117

75’ Extension Cable 9913 Equivalent 

Ultra Low Loss Coax

(3.0 dB Loss)

951107

100’ Extension Cable 9913 Equivalent 

Low Loss Coax

(4.0 db loss)

RG58U - FME connectors   /   9913 Equivalent - N connectors

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device 

must accept any interference, including interference that may cause undesired operation of this device.

The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when mul-

tiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is 

re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power 

or gain reduction and not by an attenuator at the output of the device.

The information provided by Wilson Electronics, Inc. is believed to be complete and accurate.  However, no respon-

sibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any 

infringements of patents or other rights of third parties that may result from its use.

Copyright © 2004 Wilson Electronics, Inc.