Netgear 07300070 ユーザーズマニュアル

)NSTALLATION

T

This guide describes installation for the WNHDE111 5GHz Wireless-N HD Access Point/
Bridge or the WNHDE111 HD/Gaming 5GHz Wireless-N Networking Kit. 

1.

Familiarize yourself with the features of the Wireless-N Bridge. 

The mode switch can be set to:

•

Auto. In Auto mode, the Wireless-N Bridge will automatically sense and set its 
own mode. It will run in AP mode if connected to a router or gateway. Otherwise, 
if connected to any other wired device(s), it will run in Bridge mode. (The 
Wireless-N Bridge is set to Auto mode from the factory.)

•

AP. In AP (access point) mode, the Wireless-N Bridge will act as an access point. 
In this mode, the Wireless-N Bridge should be connected to a router. 

•

Bridge. In Bridge mode, the Wireless-N Bridge is connected to your other wired 
device(s) and will connect wirelessly to the Wireless-N Bridge being used as an 
access point.

2.

Verify that:

•

You have Broadband Internet access through a powered-on router or gateway.

DEFAULT ACCESS

Power

Ethernet ports

Mode switch

Power light on/off switch

Power light

WPS button/light

•

You are connecting Ethernet-enabled devices, such as a network-enabled game 
console (an XBox 360 or Sony PS3), a digital media player (an Apple TV or 
NETGEAR Digital Entertainer), an IPTV set-top box, or a laptop with an 
embedded Wireless-N adapter. 

1.

Set the switch on the back of each Wireless-N Bridge to Auto mode.

Caution: Do not plug in the power adapter before step 2.

2.

Connect the Ethernet cable from a LAN port in the router or gateway (A) to either 
LAN port on one Wireless-N Bridge. 

3.

Place the other Wireless-N Bridge near the media player, game console, or set-top 
box (B), and connect it with an Ethernet cable.

4.

To complete installation, connect a power adapter to the Wireless-N Bridge(s). Allow 
a few minutes for your devices to connect to the Internet. If you are not connected, see 
“Troubleshooting” on page 2.

Note: By following the steps in this installation with both Wireless-N Bridge units set to 
Auto mode, the Wireless-N Bridge connected to your router has set itself to AP mode, 
while the second Wireless-N Bridge is set to Bridge mode.

Digital set-top box

Network TV 
viewer/DVR

DMA

Gaming console

WNHDE111

Network storage

Router/gateway

Desktop PC

Internet

1.

Set the switch on the back of the Wireless-N Bridge to Auto mode (it will set itself to 
AP mode).

2.

Connect the Ethernet cable from a LAN port on the router or gateway (A) to either 
LAN port on the Wireless-N Bridge. 

3.

Place your computer or other device (B) within range of the Wireless-N Bridge in AP 
mode.

4.

Connect a power adapter to the Wireless-N Bridge. 

5.

Connect your wireless clients by one of the following methods: 

•

In your client’s adapter configuration settings, to use the default WPA-PSK/
WPA2-PSK security settings, enter the SSID as NETGEAR-HD, and the 
passphrase that is printed on the Resource CD. 

•

If your wireless device has a WPS push-button, connect it to the Wireless-N 
Bridge in AP mode, similar to steps 3-5 in “To Add Another Wireless-N Bridge 
to a System with a Wireless-N Bridge in AP Mode” on page 1.

1.

Make sure the WNHDE111 5GHz Wireless-N HD Access Point/Bridge you are 
adding is not set to AP mode, place it near the devices that will work with it.

2.

Connect a power adapter to the new Wireless-N Bridge.

WNHDE111

Network storage

Router/gateway

Desktop PC

Internet

Laptop with embedded 
Wireless-N adapter

HDTV with 
Wireless-N

Wireless-N enabled set-top box

Apple TV