Maxon Electronics Australia Pty. Ltd. MM-BP3USB ユーザーズマニュアル
Page 2 of 12
FCC RF EXPOSURE COMPLIANCE
In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure
to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international
standards bodies. The design of this modem complies with the FCC guidelines and these international standards.
Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations.
This Telstra Turbo Modem™ has been tested for FCC RF exposure hand and body SAR compliance with the USB3-8521 USB Modem form factor. In order to comply with FCC RF exposure
requirements, the Telstra Turbo Modem™ must be operated with USB3-8521 USB Modem form factor.. The use of this device in any other type of host configuration may not comply with
FCC RF exposure requirements and should be avoided. During operation, a 1.5cm separation distance should be maintained between the antenna, whether extended or retracted, and the
user’s/bystander’s body (excluding hands, wrists, feet, and ankles) to ensure FCC RF exposure compliance.
to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international
standards bodies. The design of this modem complies with the FCC guidelines and these international standards.
Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations.
This Telstra Turbo Modem™ has been tested for FCC RF exposure hand and body SAR compliance with the USB3-8521 USB Modem form factor. In order to comply with FCC RF exposure
requirements, the Telstra Turbo Modem™ must be operated with USB3-8521 USB Modem form factor.. The use of this device in any other type of host configuration may not comply with
FCC RF exposure requirements and should be avoided. During operation, a 1.5cm separation distance should be maintained between the antenna, whether extended or retracted, and the
user’s/bystander’s body (excluding hands, wrists, feet, and ankles) to ensure FCC RF exposure compliance.
CAUTION
Change or modification to the modem without the express consent of Maxon Electronics Australia Pty. Ltd. voids the user’s authority to use the equipment. This equipment has been tested and
found to comply with the limits pursuant to Part 22 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in an appropriate installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not used in accordance with instructions, can cause harmful radiation to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference in radio and television reception, which can be determined by turning the
equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
found to comply with the limits pursuant to Part 22 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in an appropriate installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not used in accordance with instructions, can cause harmful radiation to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference in radio and television reception, which can be determined by turning the
equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation distance between the equipment and the receiver
•
Contact Telstra Technical Support for assistance.
All data and information contained in or disclosed by this document are proprietary information of Maxon Electronics Australia, and all rights therein are expressly reserved. By accepting this
material, the recipient agrees that this material and the information contained therein are held in trust and will not be used, copied, reproduced in whole or in part, nor its contents used in any
manner without the express written permission of Maxon Electronics Australia.
This information provided in this document is provided on an “as is” basis, is preliminary and subjected to change without notice.
In no event will Maxon Electronics Australia be liable for any damages arising directly or indirectly from any use of information contained in this document.
NOTES:
The user is cautioned that changes or modifications to the modem not expressly approved by Telstra or Maxon Electronics Australia Pty Ltd could void the warranty.
POTENTIALLY UNSAFE AREAS
Posted facilities:
Turn off this device in any facility or area when posted notices require you to do so.
Blasting areas:
Turn off your modem where blasting is in progress.
Observe restrictions and follow any regulations or rules.
Potentially explosive atmospheres:
Turn off your modem when you are in any area with a potentially explosive atmosphere. Obey all signs and instructions. Sparks in such areas could cause
an explosion or fire, resulting in bodily injury or death.
Areas with a potentially explosive atmosphere are often but not always clearly marked. They include:
Areas with a potentially explosive atmosphere are often but not always clearly marked. They include:
z
fuelling areas such as gas or petrol stations
z
below deck on boats
z
transfer or storage facilities for fuel or chemicals
z
vehicles using liquefied petroleum gas, such as propane or butane
z
areas when the air contains chemicals or particles such as grain, dust or metal powders
z
any other area where you would normally be advised to turn off your engine
It is recommended that this manual be read in conjunction with all other supporting documentation.