The Watt Stopper Inc. FSP-3X1 ユーザーズマニュアル

Single/Dual Phase (Universal), High/Low/Off,  

PIR Fixture Integrated Outdoor Sensor In IP66 Enclosure
Monophasé/Biphasé (Universel), Haut/Bas/Éteint,  

Luminaire avec capteur IRP extérieur intégré dans un boitier IP66 
Fase simple/doble (universal), Alto/Bajo/Apagado,  

Sensor exterior integrado del aplique PIR en gabinete IP66

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: xxxxx – 03/17  rev. 1

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

Voltage  ......................................100-347VAC (single phase) 
  

 ............................. 208/230/480VAC phase-to-phase

Load Ratings
 @230-240V .................... 0-300W Ballast or LED Driver
 

@ 120V ........0-800W Tungsten, Ballasts or LED Driver

 

@ 277V ........................ 0-1200W Ballast or LED Driver

 @347/480V .................. 0-1200W Ballast or LED Driver
 

Motor @ 120V/277V............................................1/6 HP

Wiring
 Length 

 .......36” (91.44cm), 30” (76.2cm) from nipple

 

Line Voltage .................................... Line, Neutral, Load

 

Low Voltage ............Dim + (violet), Dim - (gray) 18AWG

Operating Temperature ..........-40°F (-40°C) to 167°F (75°C)
Tightening Skirt/Nut Torque .................................25-30 in-lbs
Dimensions
 Collar ......................................1.30” diameter (33.0mm)
 

Collar height ..........................................0.64” (16.3mm)

 Body .....5.7”L x 2.3”W x 3.5”H (145mm x 60mm x 90mm)
Weight 2.8 oz (80 g)
Enclosure ................................................. IP66 (NEMA STD)
Coverage
 

FSP-L2 Lens @ 8’ height ..................up to 44’ diameter

 

FSP-L3 Lens @ 20’ height ................up to 40’ diameter

 

FSP-L7 Lens @ 40’ height ..............up to 100’ diameter

Adjustments and Features
 

High Mode .......................................................0 V  -10 V

 

Low Mode  .............................................. 0 V - 9.8 V, Off

 

Time Delay ......................... 30 seconds, 1 min - 30 min

 

Cut Off ..................... Disable, 1 min - 59 min ,1 hr - 5 hr

 Sensitivity .....................On-Fix, Off-Fix, Low, Med, Max
 

Hold Off Setpoint .....................Auto, None, 1 fc - 250 fc

 

Ramp Up ................................... Disable, 1 sec - 60 sec

 

Fade Down ................................ Disable, 1 sec - 60 sec

 

Photocell Setpoint for On/Off ............................1-250 fc

Factory Defaults
 

High Mode .............................................................. 10 V

 

Low Mode  ................................................................ 1 V

 

Time Delay ............................................................5 min

 

Cut Off ..................................................................... 1 hr

 Sensitivity 

 ...............................................................Max

 

Hold Off Setpoint  ...............................................Disable

 

Ramp Up ............................................................Disable

 

Fade Down .........................................................Disable

 

Photocell Setpoint for On/Off .............................Disable 

The FSP-321B is an IP66 rated motion sensor that dims lighting from high to low based 

on movement. 
Three configurations are available. The FSP-321B mounts inside the fixture and the PIR lens 

connects to the FSP-321B through a 1.30” diameter hole in the bottom of the fixture. The 

FSP-321B-S mounts to a fixture/enclosure with a 1/2” knock out, via a nipple on the back. 

The FSP-321B-D has a drop mount nipple, for mounting on to a pole, or to a fixture.
The sensor uses passive infrared (PIR) sensing technology that reacts to changes in 

infrared energy (moving body heat) within the coverage area. Once the sensor stops 

detecting movement and the time delay elapses, lights will go from high to low mode 

and eventually to an OFF position if it is desired. Sensors must directly “see” motion of a 

person or moving object to detect them, so careful consideration must be given to sensor 

luminaire placement and lens selection. Avoid placing the sensor where obstructions may 

block the sensor’s line of sight.
The FSP-321B operates at 100-347V Single Phase, as well as 208/230/480VAC phase-to-phase. No power pack is required. It is 

designed to be installed in indoor and outdoor environments.
NOTE: When the FSP-321B is powered up the first time, it the will use factory default parameters to operate. If adjustments are 

needed, the FSIR-100 configuration tool must be used.

Several lenses are available for use with the FSP-321B. Lenses give coverage at mounting heights between 8’ - 40’ for applications 

such as, offices,  warehouses and outdoor use. Density and range of the coverage  is determined by the type of lens and mounting 

height. Lens modules are IP-66 rated when combined with an FSP-321B sensor mounted to an outdoor rated fixture. See the FSP-Lx 

Coverage Guide for more information. 

Light Sensor

Motion Indicator

Blue LED

PIR Sensor