ViVOtech Inc. 030XX4K ユーザーズマニュアル
ViVOtech Confidential 7
ViVOwallet User Guide
D ra ft C opy O nl y
Customer Support
Customer Support
Technicians and installers may contact ViVOtech Inc. at
http://www.vivotech.com/support/service_request.asp to submit a service request or call the toll free
support line @ (888) 363-3753. Both are available 24 hours per day, seven days a week.
About ViVOtech
ViVOtech Inc. enables more than 30 million new and existing merchant Point of Sale (POS) systems
with rapid, scalable and cost-effective deployment of secure contactless card and mobile device
payment capabilities. ViVOtech uses its unique Dynamic Strip™ technology to upgrade an existing POS
terminal in minutes with no POS software change. ViVOtech has more than ten patents pending on
various enabling technologies.
The company is privately held and headquartered in Santa Clara, California. ViVOtech Inc.'s
The company is privately held and headquartered in Santa Clara, California. ViVOtech Inc.'s
management and advisory board include former executives from First Data Corporation, Citibank,
Diebold, Intuit, McCaw Cellular, Target Corporation, VeriFone and Visa International/USA. For more
information about ViVOtech, call (888) 363-3753, e-mail info@vivotech.com or visit www.vivotech.com.
FCC Regulatory Compliance: Notices Class B Equipment:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
interference received, including interference that may cause undesired operation.
!
WARNING:
1.The Vivopay 4000 hardware or software can not be replaced or modified by any third
party other than VIVOtech.
2. Minimum separation distance between 2 DT devices should be at least 2 feet.
3.The device should be mounted and seated on a non metal surface and be at least 6
inches far from any metal surface
1.The Vivopay 4000 hardware or software can not be replaced or modified by any third
party other than VIVOtech.
2. Minimum separation distance between 2 DT devices should be at least 2 feet.
3.The device should be mounted and seated on a non metal surface and be at least 6
inches far from any metal surface
.