Kaba Ilco Inc. CSC790 ユーザーズマニュアル
E-730/630/750/79E SERIES INSTALLATION GUIDE • PK2925-T_11_07
Page 3
Target Audience
Please read and follow all directions carefully. These
Please read and follow all directions carefully. These
instructions are designed for use by maintenance profes-
sionals or lock installers who are familiar with common
safety practices and competent to perform the steps
described. Kaba Ilco is not responsible for damage or
malfunction due to incorrect installation, that may arise.
ii introDUCtion anD DisClaimers
Please read and follow all directions carefully.
!
Important: Carefully inspect windows, doorframe, door, etc.
to ensure that the recommended procedures will not cause
damage. Kabas standard warranty does not cover damages
caused by installation.
to ensure that the recommended procedures will not cause
damage. Kabas standard warranty does not cover damages
caused by installation.
!
Caution: Wear safety glasses when making the holes.
!
i
CheCklist For stanDarD exit DeviCes
Each Generation E-730/630/750/79E lockset includes:
(A) Ouside lever handle
(A) Ouside lever handle
(B) Outside housing
(C) Battery holder with 3 AA batteries
(D) Inside dress plate
Parts inside hardware bag:
(K) 1 x Spindle
Parts inside hardware bag:
(K) 1 x Spindle
(I) 1 x Torx-head screw
(J) 3 x mounting screws (10-24,
1
/
8
” hex head)
Tools Required:
Safety glasses
Safety glasses
1
/
4
” (6.5mm) drill bit
1
/
2
” (13mm) drill bit
1” (25mm) drill bit or hole saw
Drill
Awl or center punch
Hammer
Rubber mallet
Small flat screwdriver
Torx screwdriver (T-15)
1
/
8
” Allen key
Adjustable square
Tape measure
Pencil
Tape
Cleaning supplies
(drop cloth, vacuum)
221 222 223
Inside Dress Plates
D
Dress Plate For Exit Devices
Part #
Manufactured By
061-510
221 arrow
s3808/s1808
s1908/s3908
s1708/s3708
061-510
222 von Duprin 9875/9975 eo-F,
precision 1103/ Fl1103
061-510
223 Yale
7100-36
Warnings and Conditions
B
A
C
I
K
J
D
E-730/630/750/79E SERIES INSTALLATION GUIDE • PK2925-T_11_07
Page 16
22. The cap has a small groove on one edge (to allow ease of removal)
this should be facing down. Insert bottom snap of cap (I, see page 11) in
handle hole below the cylinder. With a small screwdriver, push top snap of
cap down while pushing the cap into place to cover the keyhole (Fig. 15)
23. To remove the cap, insert a small flat screwdriver into this groove and
gently pry the cap off, being careful not to damage it. (You may want
to cover the bottom of the lever to protect the finish from being scratched
through the process of removing the cap). (Fig.16)
19. With the door open, insert key in cylinder and turn it clockwise
until it stops.
20. Let go of the key and turn the lever handle (clockwise for
right-handed and counter-clockwise for left-handed locks).
20. Let go of the key and turn the lever handle (clockwise for
right-handed and counter-clockwise for left-handed locks).
The latch
must retract.
21. Extend deadbolt and repeat the above operation (turn key clockwise
until it stops), latch and deadbolt must retract completely.
21. Extend deadbolt and repeat the above operation (turn key clockwise
until it stops), latch and deadbolt must retract completely.
Test the Mechanical Override Function (continued)
!
Verify the functionality of the override after the
lock is installed on the door:
Fig. 16
cover tHe keyHole & cylinder witH tHe cap
9.
How to cHange lock cylinders
10.
Fig. 17
24. Remove the cap from the lever handle (see step 20, Fig. 16).
25. Insert key.
26. Turn the key clockwise until it stops.
27. Release key.
28. Use a small flat screwdriver to push in the lever catch through
25. Insert key.
26. Turn the key clockwise until it stops.
27. Release key.
28. Use a small flat screwdriver to push in the lever catch through
the small hole underneath the lever handle (Fig. 17).
29. Pull the lever handle off of the lock housing (be careful not to
lose the cylinder plug).
30. Replace the old cylinder with the new one in the lever handle. Only
same kind of cylinder with 2 grooves in cross, in the end of the cylinder plug
could be used on the E-730/630 Series locks. (Fig. 18)
30. Replace the old cylinder with the new one in the lever handle. Only
same kind of cylinder with 2 grooves in cross, in the end of the cylinder plug
could be used on the E-730/630 Series locks. (Fig. 18)
Fig. 18
2 Grooves in cross
Fig. 15
(I)
Hole below cylinder
Bottom snap (First)
Bottom snap (First)
Top snap (Second)
Push (Third)