Asia Bright Industrial Co. Ltd. AS-CF125-T ユーザーズマニュアル
GENERAL INFORMATION Model:AS-CF125N
FCC
ID
:
QJ4AS-CF125-R
for
Receiver
FCC ID : QJ4AS-CF125-T for Transmitter
This remote control is designed to separately control your ceiling fan speed and light brightness.
There are two buttons (fan and light) to control the fan speed and light.
The fan button will control fan speeds (Hi、Med、Low)
The light dimmer button will control the light.
INSTALLATION AND OPERATING INSTRUCTIONS
Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
! QUALIFIED PERSON ONLY CARRIES OUT INSTALLATION.
ONLY INSTALL TO CONCRETE CEILING
1. SETTING
THE
CODE
The unit has 16 different code combinations to set the codes. Perform these steps:
A. Setting the codes on the transmitter.
A. Setting the codes on the transmitter.
a.
Remove battery cover. Press firmly below arrow and slide battery cover off.
b.
Slide code switches to your choice of up or down position.(Factory setting
is all up).Do not use the position use a small screwdriver or ball point pen
to slide firmly up or down (Figure 1).
is all up).Do not use the position use a small screwdriver or ball point pen
to slide firmly up or down (Figure 1).
c.
Replace battery cover on transmitter.
B.
Setting code on the receiver.
a.
a.
Slide code switches to the same positions as set on your transmitter (Figure 2).
2.
INSTALLING RECEVIER IN CEILING FAN
A. Safety
precautions:
WARNING:HIGH VOLTAGE!
Please use a qualified and licensed electrician.
Household electrical power can cause serious injury or death.
Disconnect source of electrical power to the ceiling fan by removing fuse or switching off circuit breaker.
Do not use with solid state ceiling fans.
Electrical wiring must meet all local and National Electrical Code requirements.
Electrical source and fan must be 115/120 volts,60HZ.Maximum fan motor amps: 1.0 and maximum light watts:300 incandescent only.
Please use a qualified and licensed electrician.
Household electrical power can cause serious injury or death.
Disconnect source of electrical power to the ceiling fan by removing fuse or switching off circuit breaker.
Do not use with solid state ceiling fans.
Electrical wiring must meet all local and National Electrical Code requirements.
Electrical source and fan must be 115/120 volts,60HZ.Maximum fan motor amps: 1.0 and maximum light watts:300 incandescent only.
B.
Installing receiver in fan:
MOTOR AC -L
LIGHT
AC-N
COM
ANTENNA
.
3.
OPERATING
TRANSMITTER:
A.
Install 9 volt battery (not included). To prevent damage to transmitter ,remove the battery if not used for long periods.
CODE
TRANSMITTER
RECEIVER
CODE
Figure 2
Figure 1
a.
Remove ceiling fan canopy from the mounting bracket.
b.
Disconnect existing wiring between ceiling fan and supply at
electrical unction box
c.
c.
Lay the back antenna wire on top of the receiver and put the
receiver in the mounting bracket.
d.
d.
Make wiring connections as follows :using the wire nuts supplied
CONNECT TO
CONNECT TO
Black receiver wire (ACN)---------------- AC Supply N
White receiver wire (ACL)--------------- -AC Supply L
White receiver wire (COM )---------------Output COM L
Black receiver wire (FAN)----------------- Fan N
Blue receiver wire (LIGHT)--------------- Light N
White receiver wire (ACL)--------------- -AC Supply L
White receiver wire (COM )---------------Output COM L
Black receiver wire (FAN)----------------- Fan N
Blue receiver wire (LIGHT)--------------- Light N
e.
Push all connected wire up into junction box.
f.
Reinstall the canopy on the mounting bracket.
g.
Make sure the black antenna is visible after canopy has been installed.
h. Restore
electrical
power.
i.
Figure 3 install receiver
ceiling fan chart
B.
Store the transmitter away from excess heat or humidity.
C.
This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other
remote units such as garage door openers .car alarm or security system. If you find that your fan and light kit go on
and off without using your remote control simply change the combination code in your transmitter and receive.
remote units such as garage door openers .car alarm or security system. If you find that your fan and light kit go on
and off without using your remote control simply change the combination code in your transmitter and receive.
D.
Operation buttons on the panel of the transmitter.
The fan button will control the fan speeds (Hi、Med、Low、Off )
The fan button will control the fan speeds (Hi、Med、Low、Off )
The light button will control the light brightness
The light function is controlled by pressing the light button. Hold button down to increase or decrease light .Tap button quickly to turn.
Light off or on .if you press the button in excess of 0.7 second it become a dimmer .
The light key has auto resume so will stay at the same brightness as the last time it is turned off.
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT
The light function is controlled by pressing the light button. Hold button down to increase or decrease light .Tap button quickly to turn.
Light off or on .if you press the button in excess of 0.7 second it become a dimmer .
The light key has auto resume so will stay at the same brightness as the last time it is turned off.
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT