Aten KL1508AM クイック設定ガイド

1

3

1 KL1508

A

 or KL1516

A

 Cat 5 High-Density Dual Rail LCD KVM Switch 

   with Standard Rack Mount Kit

1 Firmware Upgrade Cable

1 Power Cord

1 User Instructions

5

4

1, Upper Handle

2. LCD Module

3. Keyboard Module

4. Lower Handle

5. Power LED

6. Keyboard Release Catch

7. LCD Release Catch

8. Rack Mounting Tabs

Depending on any optional equipment that you may have purchased, one of the following 

may be included in your package:

• Standard Rack Mount Kit - Long

• Easy Installation Rack Mount Kit - Short

• Easy Installation Rack Mount Kit - Long

Note: The front and rear panel views are similar for the KL1508

A

, the difference being that 

the KL1508

A

 has only 8 buttons on the control pad and 8 ports in the real panel.

A standard rack mounting kit is provided 

with your KL1508

A

 / KL1516

A

. The kit 

enables the switch to be mounted in rack 

with a depth of 42–77 cm.

To rack mount the switch, do the following:

1. While one person positions the switch in 

the rack and holds it in place, the second 

person—using the screws provided with 

the rack mounting kit— loosely screws 

the front brackets to the rack.

2. While the first person still holds the 

switch in place, the second person slides 

the L brackets into the switch's side 

mounting brackets, from the rear until the 

bracket flanges contact the rack, then – 

using the screws provided with the rack 

mounting kit – screws the L brackets to 

the rack

3. After the L brackets have been secured, 

tighten the front bracket screws.

In a single stage installation, there are no additional KVM switches daisy chained down from the 

KL1508

A

 / KL1516

A

. To set up a single stage installation, refer to the installation diagrams (the 

numbers in the diagram correspond with the numbers of the instruction steps), and do the following:

1. Ground the KL1508

A

 / KL1516

A

 by connecting one end of the grounding wire provided with your 

switch to the grounding terminal, and the other end of the wire to a suitable grounded object.

Note: Do not omit this step. Proper grounding helps to prevent damage to the unit from surges or 

static electricity

2. Plug the console keyboard, monitor, and mouse into the unit’s console ports. The ports are color 

coded and marked with icons for easy identification.

Note: You can use any combination of keyboard and mouse connections. For example, you can use a 

PS/2 keyboard with a USB mouse.

3. Use Cat 5e/6 cable to connect any available KVM port to a KVM adapter cable that is appropriate 

for the computer you are installing. 

Note: To support a resolution of 1280x1024, the recommended maximum distance between the unit 

and the KVM adapter cable is 50 meters.

4. Connect the KVM adapter cable to the computer.

Plug the connectors on the KVM adapter cable into the appropriate ports of the computer you are 

installing.

5. Plug the female end of the power cord into the KL1508

A

 / KL1516

A

's power socket; plug the male 

end into an AC power source. 

After the KL1508

A

 / KL1516

A

 is cabled up, you can turn on the power. After it is powered up, you 

can turn on the servers

• A VGA, SVGA, or multisync monitor capable of the highest resolution that you will be using on 

any computer in the installation

• A PS/2 or USB mouse

• A PS/2 or USB keyboard

The following equipment must be installed on the computers that connect to the KL1508

A

 or 

KL1516

A

 KVM ports:

• A VGA, SVGA or multisync port

• A Type A USB port and USB host controller (for USB KVM adapter cable connection, see 

following section)

- or -

• 6-pin Mini-DIN keyboard and mouse ports (for PS/2 KVM adapter cable connection, see 

following section)

• Cat 5e/6 cable is required to connect the KL1508

A

 / KL1516

A

 to one of the KVM adapter cables.

• The following KVM adapter cables are required for use with the KL1508

A

 / KL1516

A

:

2

Connect to devices with PS/2 ports  

KA7920 / KA7520 / KA7120 / KA9520 / KA9120 

Connect to devices with USB ports  

KA7970 / KA7570 / KA7170 / KA9570 / KA9170 

Connect to Sun Legacy systems (with 13W3 port)   KA9130 / KA7130 

Connect to Sun USB systems  

KA9170 / KA7170 

Connect to serial based devices  

KA9140 

2

4

1

3

1 Keyboard

2 Touchpad

3. External Mouse Port

4. Station ID LED

5. Station Selection Area

6. Lock LEDs & Reset Switch

7. Port Selection Buttons and LEDs

1. LCD Display

2. LCD Controls

3. LCD On/Off Button

4. Firmware Upgrade Section

4. Daisy Chain Ports

5. Console Ports Section

6. KVM Port Section

1. Grounding Terminal

2. Power Socket 

3. Power Switch

L Brackets

Side Mounting

Bracket (Typ.)

7

6

8

1

5

4

2

3

1

7

6

3

4 5

2

© Copyright 2012 ATEN

®

 International Co., Ltd.   www.aten.com

Altusen and the Altusen logo are trademarks of ATEN International Co., Ltd. 
All rights reserved. All other trademarks are the property of their respective owners.
This product is RoHS compliant    

 

All information, documentation, and specifications contained in this media are subject to change without prior notification by the manufacturer. 
Please visit our website to find the most up to date version. 

DE 102004019107
CN ZL 02122202.9
CN ZL 200410031689.0
CN ZL 200410042771.3
CN ZL 200510071431.8
CN ZL 200610007185.4

CN ZL 200610145931.6
CN ZL 200610079265.0
CN ZL 200610081929.7
TW 183765
TW I237762
TW I269992

TW I273372
TW I288595
TW I325748
TW I327054
TW I340311
US 7386584

US 7640289
US 7613854
US 7584309
US 7405926
US 7258568
US 7414853

US 7675742
US 7505255
US 6160543
GB 2412456
GB 2425661
FR 0500514 

JP 4456936
JP 4500751

Online Registration
International:
• http://support.aten.com
North America:
• http://www.aten-usa.com/product_registration  

 
Technical Phone Support
International:
• 886-2-8692-6959
China:
• 86-10-5255-0110
Japan:
• 81-3-5615-5811
Korea:
• 82-2-467-6789
North America:
• 1-888-999-ATEN   Ext: 4988  
United Kingdom:
• 44-8-4481-58923