Ewig Industries Macao Commercial Offshore Limited 693500 ユーザーズマニュアル
INSTRUCTION MANUAL MODEL ET-71 REDI CHEK
®
REMOTE
Introduction
Congratulations on your purchase of the Redi Chek
Congratulations on your purchase of the Redi Chek
®
Remote, a programmable radio
frequency food thermometer. You will now be able to remotely monitor the temperature of
food cooking in the oven or outdoors from anywhere in your home.
food cooking in the oven or outdoors from anywhere in your home.
Components
1. 1 - silver receiver unit
2. 1 - silver transmitter unit
3. 1 - detachable stainless steel probe sensor
4. 4 - AAA batteries
1. 1 - silver receiver unit
2. 1 - silver transmitter unit
3. 1 - detachable stainless steel probe sensor
4. 4 - AAA batteries
Receiver Features
LCD (Liquid Crystal Display) – Displays all icons, temperature. See LCD diagram for
detailed information.
detailed information.
CLIP – Removable clip allows you to be mobile. Clip the receiver unit to belt.
BATTERY COMPARTMENT – Holds 2 AAA batteries.
STAND – Swings out and allows you to stand the receiver on tabletop.
Buttons
1.
1.
-In normal model. Press & hold for 1 seconds, on/off the temperature alarm. In
setting mode, press the “
” key will increase the setting value. Press and hold the up
key more than 2s, will fast forward the setting value by about 8 steps/s. Further holding
the “
the “
” key more than 5s, will fast forward the setting value by about 16 steps/s.
2.
-In normal mode, Press & hold for 1 seconds, select temperature readings in Celsius
or Fahrenheit. In setting mode, press the “
” key will decrease the setting value. Press
& hold the “
” key more than 2s, will fast backward the setting value by about 8steps/
s. Further holding the “
” key more than 5s, will fast backward the setting value by
about 16 steps/s.
3. ON/OFF – Turns receiver functions on and off.
4. In normal mode, press “
” and “
” key together will enter setting mode. In the
setting mode, press “
” and “
” key together or no key press about 5 second will exit
setting mode.
Transmitter Features
STAND – Swings out and allows you to stand receiver on tabletop.
BATTERY COMPARTMENT – holds 2 AAA batteries.
S – plug in for stainless steel probe sensor
Buttons
1. TX – transmit manually, terminates the auto registration process. Press and hold for 2
1. TX – transmit manually, terminates the auto registration process. Press and hold for 2
seconds to register the radio frequency with the receiver.
2. ON/OFF – on normal operation with full function. Off turns transmitter off.
Registration Procedures
Open the battery compartment of receiver and insert the two “AAA” batteries. Open the
battery compartment of transmitter and insert the two “AAA” batteries.
Open the battery compartment of receiver and insert the two “AAA” batteries. Open the
battery compartment of transmitter and insert the two “AAA” batteries.
The Redi Chek
®
Remote needs the receiver to register the radio frequency signal from the
transmitter.
Transmitter & Receiver are off.
1.Plug the stainless steel probe sensor into the plug in of the transmitter.
1.Plug the stainless steel probe sensor into the plug in of the transmitter.
2.Turn the receiver on by push switch on the rear of the receiver from OFF to ON.
3. Turn unit on by pressing switch on the rear of the transmitter from OFF to ON. This
needs to be done within 60 seconds of turning on the receiver in order for the receiver to
register the signal from the transmitter. If it doesn’t beep within 5-10 seconds slide
switch OFF wait a few seconds and then switch back ON.
register the signal from the transmitter. If it doesn’t beep within 5-10 seconds slide
switch OFF wait a few seconds and then switch back ON.
4. Registration is complete when the unit beeps and the probe temperature appears where
the “---” was flashing.
Transmitter is already on.
1. Plug the stainless steel probe sensor into the plug in of the transmitter.
1. Plug the stainless steel probe sensor into the plug in of the transmitter.
2. Turn the receiver on by sliding switch on the rear of the receiver from OFF to ON.
3. Press and hold TX for 2 seconds on the rear of the transmitter. This needs to be done
within 60 seconds of turning on the receiver in order for the receiver to register the
signal from the transmitter. Once TX is released it will take several seconds for the
receiver to register. If it doesn’t beep within 5-10seconds press and hold TX again.
signal from the transmitter. Once TX is released it will take several seconds for the
receiver to register. If it doesn’t beep within 5-10seconds press and hold TX again.
4. Registration is complete when the unit beeps and the probe temperature appears where
the “---” was flashing.
Receiver and transmitter are already on.
1. Plug the stainless steel probe sensor into the plug in of the transmitter.
1. Plug the stainless steel probe sensor into the plug in of the transmitter.
2. Press and hold TX for 2 seconds on the rear of the transmitter. This needs to be done
within 60 seconds of pressing MODE on the receiver in order for the receiver to
register the signal from the transmitter. Once TX is released it will take several seconds
for the receiver to register. If it doesn’t beep within 5-10 seconds press and hold TX
again.
register the signal from the transmitter. Once TX is released it will take several seconds
for the receiver to register. If it doesn’t beep within 5-10 seconds press and hold TX
again.
3. Registration is complete when the unit beeps and the probe temperature appears where
the “---” was flashing.
Procedure for typical use on an outdoor grill:
The following typical example will go through the steps to have the Redi Chek
The following typical example will go through the steps to have the Redi Chek
®
Remote
alert you to when a beef steak is cooked.
LCD
FRONT
BACK
STAND
BATTERY COMPARTMENT
CLIP
3
2
1
ON
OFF
FRONT
BACK
SIDE
LCD
STAND
BATTERY COMPARTMENT
1
2
2