Ewig Industries Macao Commercial Offshore Limited GRP008 ユーザーズマニュアル

Open size: 490mm X 105mm

Fold size:  70mm X 105mm

Smart Home User Instruction Manual

Front side

490mm

1

0

5

m

m

Back side

Ethernet cable connector

a.Make sure 1m distance 

between Gateway and 

Modem to ensure RF 

function;

b. When the gateway turn on,

the lights start to blink. When 

the power light stays 

continuously on,the gateway 

is ready;

Gateway Installation

1. Power LED - Green LED. It does show Ethernet activities;
2. Zigbee LED - Orange LED. It is used to provide information 
     on some special cases;
3. Error LED - Red LED. It is used to indicate error cases. 

reset

Temperature sensor

Water Leakage sensor

Hardware Installation

Modem

1m

3

2

1

Make sure the dots on devices are 

close to each other

1.Press “add devices” to add sensor;
2.Select sensor type;
3.Pull out the insulation sheet ;
4.Select the install place for sensor;
5. Add others sensor as same step;

reset

reset

pairing indicator

pairing indicator

reset pairing indicator

probe

Sensor Installation

PIR sensor

 Connect the Gateway to internet via modem; 

  5V Adapter Connector

* This device design for indoor using, 

   no waterproof function;

Gateway

Ethernet Cable

5V Adaptor

 6th Step

User interface

https://play.google.com/store/apps/details?id=com.dsr.cloud.app

Scan QR code or type below link directly

 

 

Smart Home system include following essentials:

 

     1st Step

APP download, install 

 

Click the download to install APP automatically

remove 

before 

using

remove 

before 

using

remove 

before 

using

4th step: 

Add gateway

5th step: 

Add sensor 

2nd step: 

sign up, login 

3rd step: 

Identify location 

reset

pairing indicator

Please pull out the insulation sheet 

when the first time using. 

Place the device on the position 

want to install. 
Clean the surface of the install position

Please pull out the insulation sheet 

when the first time using. 

Place the device on the position 

want to install. 
Clean the surface of the install position

remove 

before 

using

reset

pairing indicator

Please pull out the insulation sheet 

when the first time using. 

Place the device on the position 

want to install. 
Clean the surface of the install position

Please pull out the insulation sheet 

when the first time using. 

Place the device on the position 

want to install. 
Clean the surface of the install position

Door/Window sensor

Tie the cable by velcro, 

ensure the probe can 

touch to water

Main body Vice body

GRP001

PIR sensor

GRP002 

Door/window sensor

GRP006 

Water leakage sensor

GRP007 

Temperature sensor 

GRP008 

Indoor sensor

Indoor sensor

Open the casing by detaching the back plate;

Place AA batteries into compartment;

Drill a hole in the wall at about 1.4 meters high, 

use the provided wall plug to turn the screw in the wall;

Mount the sensor by sliding the hole in the top of back plate;

This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential installation. 

This equipment generates, uses andcan radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference

 to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation. 

If this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is encouraged 

to try to correctthe interference by one or more of the following measures: 

-- Reorient or relocate the receiving antenna. 

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the 

   receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Changes or Modifications not expressly approved by the party

responsible could void the user’s authority to operate this device. 

This equipment complies with the FCC RF radiation exposure limits set forth for an 

uncontrolled environment. This equipment should be installed and operated with a 

minimum distance of 20 centimeters between the radiator and your body.