Novatel Wireless NRM-U630 ユーザーズマニュアル
M
M
E
E
R
R
L
L
I
I
N
N
U
U
6
6
3
3
0
0
U
U
S
S
E
E
R
R
G
G
U
U
I
I
D
D
E
E
P
P
A
A
G
G
E
E
4
4
1
1
GU-90023
Revision 1
Revision 1
Ø Near Medical and life support equipment
o
Do not operate your modem in any area where medical equipment, life support equipment, or near
any equipment that may be susceptible to any form of radio interference. In such areas, the host
communications device must be turned off. The modem may transmit signals that could interfere
with this equipment.
communications device must be turned off. The modem may transmit signals that could interfere
with this equipment.
Ø On an aircraft, either on the ground or airborne
o
In addition to FAA requirements, many airline regulations state that you must suspend wireless
operations before boarding an airplane. Please ensure that the host device is turned off and your
modem is removed from the card slot prior to boarding aircraft in order to comply with these
regulations. The modem can transmit signals that could interfere with various onboard systems and
controls.
modem is removed from the card slot prior to boarding aircraft in order to comply with these
regulations. The modem can transmit signals that could interfere with various onboard systems and
controls.
Ø While operating a vehicle
o
The driver or operator of any vehicle should not operate a wireless data device while in control of a
vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In
some countries, operating such communications devices while in control of a vehicle is an offence.
some countries, operating such communications devices while in control of a vehicle is an offence.
Ø Electrostatic Discharge (ESD)
o
Electrical and electronic devices are sensitive to electrostatic discharge (ESD). The MobiLink software
will attempt to re-initialize the device should a substantial electrostatic discharge reset the device. If
the software is not operational after an ESD occurance, then restart MobiLink. See section 2.1.4.
the software is not operational after an ESD occurance, then restart MobiLink. See section 2.1.4.
7.3 REGULATORY NOTICES
This device has been tested to and conforms to the regulatory requirements of the European Union and has
attained CE Marking. The CE Mark is a conformity marking consisting of the letters "CE". The CE Mark applies to
products regulated by certain European health, safety and environmental protection legislation. The CE Mark is
obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.
The CE Marking is not a quality-mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings are voluntary.
The product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. The applicable sections of the following standards are used to demonstrate compliance to this
requirement.
attained CE Marking. The CE Mark is a conformity marking consisting of the letters "CE". The CE Mark applies to
products regulated by certain European health, safety and environmental protection legislation. The CE Mark is
obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.
The CE Marking is not a quality-mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings are voluntary.
The product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. The applicable sections of the following standards are used to demonstrate compliance to this
requirement.
R&TTE REQUIREMENT
DESCIPLINE APPLIED STANDARD
Article 3.1(a)
Health
ICNIRP 1998
European Council Rec. 1999/519 EC
European Council Rec. 1999/519 EC
Article 3.1(a)
Safety
IEC 60950-1
Article 3.1(b)
EMC
EN 301 489-1
EN 301 489-7
EN 301 489-24
EN 301 489-7
EN 301 489-24
Article 3.2
Spectrum
EN 301 511
EN 301 908-1
EN 301 908-2
EN 301 908-1
EN 301 908-2