OKAYO Electronics Co. Ltd. DGBDUT ユーザーズマニュアル
11/15
DigiBee Group Guide System
DigiBee Group Guide System
Specifications are subject to change without prior noite.
※
Transmitter
Channel synchronization
Press mute/sync button on transmitter before it is on.
Turn the transmitter on and purple LED flashes to indicate the activation
Turn the transmitter on and purple LED flashes to indicate the activation
of channel-sync mode.
Turn receiver(s) on to be channel synchronized (one or multiple receivers
Turn receiver(s) on to be channel synchronized (one or multiple receivers
can be turned on at the same time).
When channel is successfully synchronized, receiver's LCD shows same
channel as that of transmitter's and its LED turns steady blue.
When channel is successfully synchronized, receiver's LCD shows same
channel as that of transmitter's and its LED turns steady blue.
Press mute/sync button of transmitter again to escape from sync setup.
Note
1.To re-activate channel-sync mode, please turn the transmitter off and follow
above steps again.
2.After the transmitter escapes from channel-sync mode, its sound will be
muted when mute/sync button is pressed.
3.If the channel is not successfully synchronized, turn receiver(s) off and then
on again to be re-synchronized.
4.Maximum synchronized range is 1 meter. Out of the limited rage might result
in failed connection.
above steps again.
2.After the transmitter escapes from channel-sync mode, its sound will be
muted when mute/sync button is pressed.
3.If the channel is not successfully synchronized, turn receiver(s) off and then
on again to be re-synchronized.
4.Maximum synchronized range is 1 meter. Out of the limited rage might result
in failed connection.
Setup/Installation
Power on/off
Press and hold power button for 1 sec. to power the
device on. LCD screen shows" "and then last used
channel.
Press and hold power button for 2 sec. to power the
device off. LCD screen shows" " and then shuts down.
Channel lock/unlock
Channel will automatically be locked and symbol " "
shows up if the device is idle for 5 seconds after being
turned on.
To unlock the channel, press buttons
To unlock the channel, press buttons
and simultaneously
for 2 seconds until symbol " "disappears.
Channel selection
Press button or to select preferred channel when
channels are unlocked.
Power saving (receiver only)
Power of receivers will be off if no signal is received for 20 minutes.
Sensitivity adjustment (transmitter only)
When channel is locked, press and hold for 2 seconds to enter
mode .
Press button and to adjust the sensitivity (default: ,
).
~
Press power button to confirm the setting.
Receiver
6
7
7
8
1
2
3
4
5
5
9
7 Up/Down button
8 Power button
12
Lanyard tie-up
9 Inbuilt microphone
10
Mic-in socket
11
Mute/Sync button
9
7
8
6
1
2
3
4
5
5
4 LCD channel lock
3 LCD battery status
L
2 Power/Signal indicator
5
LCD selected channel
6 Aux-in socket
1 External Antenna
1
4 LCD channel lock
2
3 LCD battery status
Power/Signal indicator
6
5
LCD selected channel
Volume wheel
9
7
8
Up/Down button
Power button
Earphone socket
External Antenna
12
11
10
Power/Signal indicator
Indicator behavior
Transmitter
Receiver
Flash
Steady
No LED
Red
Blue
Purple
Low battery&
Mute activated
Mute activated
Low battery&
Signal transmitted
Sufficient battery&
Signal transmitted
Signal transmitted
Sufficient battery&
Signal transmitted
Sufficient battery&
Mute activated
Mute activated
Red
Low battery&
Signal received
Signal received
Blue
-
-
-
Sync activated
Sufficient battery&
Signal received
Signal received
Signal is not received
Device is not turned on
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding
the RF exposure requirements and void user’s authority to operate the device.
FCC INFORMATION
The Federal Communication Commission Radio Frequency Interference Statement includes the
following paragraph:
The equipment has been tested and found to comply with the limits for a Class B Digital Device,
The equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction,
may cause harmful interference to radio communication.However, there is no grantee that
interference will not occur in a particular installation. If this equipment dose cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on , the user is encouraged to try to correct the interference by one or more of the following
measures:
Notice:
The changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.