Nortek Security & Control LLC/GTO Access SGER ユーザーズマニュアル
The SGER series of digital receivers are wireless radio controls designed for use
with automatic gate openers or garage door operators. The radio format provides
unparalleled security. Receivers and transmitters do not contain a typical “coding
switch”. Each transmitter is pre-set at the factory to a unique code. The receiver
is programmed by sending a signal to it from the transmitter(s) that are going to
be used with it. This stores the transmitters code into the receiver’s memory. The
receiver will retain its memory even without power. The receiver will activate only
from these “memorized” transmitters.
with automatic gate openers or garage door operators. The radio format provides
unparalleled security. Receivers and transmitters do not contain a typical “coding
switch”. Each transmitter is pre-set at the factory to a unique code. The receiver
is programmed by sending a signal to it from the transmitter(s) that are going to
be used with it. This stores the transmitters code into the receiver’s memory. The
receiver will retain its memory even without power. The receiver will activate only
from these “memorized” transmitters.
The receivers can operate from 10.5-30 volts DC and are normally powered from
the gate operator. The relay contact(s) are rated at 5 amps @ 32 volts AC/DC NEC
Class 2 circuit.
the gate operator. The relay contact(s) are rated at 5 amps @ 32 volts AC/DC NEC
Class 2 circuit.
NOTE: SGER only works with SGET.
The SGER series has an “F” connector for attaching an antenna. The receiver is
supplied with a 9-inch local antenna, a three foot 75 ohm coaxial cable, and a
bulkhead connector for mounting the antenna outside the gate operator enclosure.
supplied with a 9-inch local antenna, a three foot 75 ohm coaxial cable, and a
bulkhead connector for mounting the antenna outside the gate operator enclosure.
Connect the appropriate channel wires (Ch. 1 - two gray wires)., (Ch. 2 - two
yellow wires) to the appropriate activation terminals on the gate operator.
yellow wires) to the appropriate activation terminals on the gate operator.
Connect the red power input wire to the radio power and the black wire to the
common terminal on the gate operator.
common terminal on the gate operator.
Use the screws provided to mount the receiver within the operator housing. This
provides protection from the elements. Secure case with case screws.
provides protection from the elements. Secure case with case screws.
Connect the coaxial cable to the “F” connector on the receiver. Drill a 3/8”
hole on the top of the operator housing for the bulkhead connector. Insert the
connector and secure it with the nut and lock washer. Connect the cable and
antenna to the bulkhead connector.
hole on the top of the operator housing for the bulkhead connector. Insert the
connector and secure it with the nut and lock washer. Connect the cable and
antenna to the bulkhead connector.
To open the receiver case, remove the screws, squeeze sides of case and rotate
upward.
upward.
The pushbutton labeled LEARN 1 is used to program transmitters to channel one.
PRINTERS INSTRUCTIONS
INSTR,INSTL,SGER SERIES - GTO P/N:
INSTR,INSTL,SGER SERIES - GTO P/N:
10016916
- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - SIDE 1 of 2
RECEIVER
LOCAL
ANTENNA
BULKHEAD
CONNECTOR
3-FOOT
CABLE
CASE SCREWS
MOUNTING
HARDWARE
WASHER
NUT
COMMON
OPEN OBSTRUCTION
INPUT
INPUT
COMMON
CLOSE OBSTRUCTION
INPUT
INPUT
10.5-30 VOLT DC
POWER
POWER
MOUNT RECEIVER
INSIDE GATE
HOUSING
SECURE CASE
CLOSED WITH TWO
SCREWS AT BOTTOM
OF CASE
CONNECT COAXIAL
CABLE TO "F"
CONNECTOR
SLIDE WEATHER
RESISTANT CAP
OVER CONNECTION
INSERT BULKHEAD
CONNECTOR THROUGH
OPERATOR HOUSING
SECURE CONNECTOR
TO HOUSING USING
WASHER AND NUT
CONNECT CABLE TO
BULKHEAD CONNECTOR
SQUEEZE BOTH SIDES AT TABS
AND TILT UPWARD
SGER
DIGITAL GATE
RECEIVER
RECEIVER
Installation Instructions
PRO ACCESS
TM
Description
STEP 1 Connect receiver relay output
STEP 2 Connect receiver to power
STEP 3 Mount the receiver
STEP 4 Connect antenna
STEP 5 Open receiver case
STEP 6a SGER channel one learn switch
Linear PRO Access • 3121 Hartsfield Road • Tallahassee, FL 32303
1.800.543.4283 • linearproaccess.com
LEARN 1
LEARN 2
CHANNEL ONE
PUSHBUTTON
USE THIS
PUSHBUTTON
TO ENTER A
TRANSMITTER
INTO CHANNEL
ONE
LEARN 1