Nortek Security & Control LLC/GTO Access GDKPD318B ユーザーズマニュアル

Copyright © GTO Access Systems 2015                                          10007727

This Digital Keypad is designed for use with automatic garage door 
operators. The radio format provides unparalleled security with more than 
a million different codes.

To activate the door operator, the user enters their unique 1 to 6 digit long 
code on the unit’s keypad and presses the 

START/STOP button. For up to 30 

seconds after the last activation, the keypad can be re-triggered by simply 
pressing the 

START/STOP button again. This allows the user to stop or 

reverse the opener quickly, without having to re-enter their code.

The keypad has built-in lighting for use at night or in dark areas. The clear 
silicone keys are backlit with a pleasing blue glow. By pressing the 

STOP button first, before entering their code, the user can light up the 

keypad.  Pressing the 

START/STOP button twice at any time will light up 

the keypad.

The keypad lockout timer will disable the keypad after 10 activations. The 
keypad must remain idle for 30 seconds before new attempts.

The garage door operator contains a built-in receiver that is programmed by 
sending a signal from the user’s transmitters. This stores the transmitter’s 
code into the receiver’s memory. The receiver will retain its memory even 
without power and will only activate from these “memorized” transmitters. 
Each keypad code can be considered a different transmitter.

INSTR,INSTL,MDTK,PVT LBL - GTO P/N:

 10007727

 - INK:

 BLACK - MA

TERIAL:

 20 LB.

 MEAD BOND - SIZE:

 11.000”

 X 8.500”

 - SCALE:

 1-1

ADDING A KEYPAD CODE

1

PRESS THE OPERATOR'S LEARN 
BUTTON FOR 1 SECOND AND RELEASE.

 
THE OPERATOR SHOULD BEEP AND THE 
LIGHT SHOULD BLINK ONCE.

 
THE RED LED WILL REMAIN LIT (LEARN 
REMOTE MODE).

2

WHILE THE RED LED IS ON, 
ENTER A 1-6 DIGIT KEYPAD CODE 
THEN PRESS AND HOLD THE KEYPAD'S 
START/STOP KEY UNTIL THE OPERATOR 
BEEPS AND THE LIGHT BLINKS ONCE.

3

REPEAT STEPS 1 & 2 FOR ANY
 ADDITIONAL KEYPAD CODES

W

X

G

H

I

D

E

F

AB

J

K

L

M

N

O

R

S

T

U

V

SCREW
PLUGS

SCREW
ANCHORS

MOUNTING
SCREWS

KEYPAD

HINGED COVER
PROTECTS THE 
KEYPAD

SOFT BLUE LIGHTS
ILLUMINATE THE KEYS
FOR NIGHTTIME USE

START/STOP BUTTON STAYS ACTIVE FOR
30 SECONDS AFTER A CODE IS USED SO THE 
OPENER CAN BE STOPPED OR REVERSED

TEN KEYS ENTERING 
1-6 KEYPAD CODES
USING NUMBERS OR LETTERS

 

MOUNT THE KEYPAD IN
CLEAR VIEW OF THE DOOR
WITH THE TWO SCREWS SUPPLIED

USE THE SCREWS 
ANCHORS SUPPLIED
IF REQUIRED

SCREWS 
ANCHORS

PUSH IN THE
TWO SCREW
COVER TO HIDE
THE SCREWS

1

2

PRESS START/STOP (LIGHTS KEYPAD) 

1

2

3

PRESS THE LIGHT (      ) BUTTON TO TURN THE OPERATOR’S LIGHT ON/OFF
(KEYPAD MUST HAVE AT LEAST ONE CODE PROGRAMMED INTO THE OPERATOR)

1

1-6 DIGIT KEYPAD CODE THAT
WAS ENTERED INTO OPENER

ENTER THE KEYPAD CODE

PRESS START/STOP

ENTER THE KEYPAD CODE

PRESS START/STOP 

1-6 DIGIT KEYPAD CODE THAT
WAS ENTERED INTO OPENER

 

 

1

3

4

2

REMOVE THE TWO
SCREWS AND SLIDE
THE BATTERY COVER OFF 

 
 

REMOVE THE 
LOW VOLTAGE
BATTERIES AND 
DISPOSE OF THEM 
PROPERLY

INSTALL 3 FRESH
AAA BATERIES

 

 
 

 

BE SURE THE 
SILICONE GASKET
IS IN PLACE

 

REPLACE THE
BATTERY COVER
AND RE-INSTALL 
THE TWO SCREWS

 

 

 

 

This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that may cause undesired operation.
 
NOTE: This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio or television reception, which can 
be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:
 
•   Reorient or relocate the receiving antenna.
•   Increase the separation between the equipment and receiver.
•   Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.

•   Consult the dealer or an experienced radio/TV technician for help.

CAUTION!
Any changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.

This product is warranted to the original consumer against defects in material and workmanship 
for the periods mentioned above. GTO Access Systems will repair, or at its option, replace, any 
device that it finds requires service under this warranty. This warranty does not apply to damage 
to the product from negligence, abuse, abnormal usage, misuse, accidents, normal wear or tear 
or due to failure to follow Seller’s instructions, or arising from improper installation, storage or 
maintenance. In no event will GTO Access Systems be responsible for incidental, compensatory, 
punitive, consequential, indirect, special or other damages. The remedies provided by this 
warranty are exclusive. Some states do not allow the exclusion or limitation of incidental 
and consequential damages, so the above limitation or exclusion may not apply to you. Any 
warranties implied by law are limited to the time periods set forth above. Some states do not 
allow limitations on how long an implied warranty lasts, so the above limitation may not apply 
to you. This warranty gives you specific legal rights, and you may also have other rights which 
vary from state to state.
For warranty service, contact GTO Access Systems at 800-543-1236. In order to be protected by 
this warranty, save your proof of purchase should repair be required.

Radio controls provide a reliable communications link and fill an important need in portable 
wireless signaling. However, there are some limitations which must be observed.
•  For U.S. installations only: The radios are required to comply with FCC Rules and 

Regulations as Part 15 devices. As such, they have limited transmitter power and therefore 
limited range.

•  A receiver cannot respond to more than one transmitted signal at a time and may be 

blocked by radio signals that occur on or near their operating frequencies.

•  Changes or modifications to the device may void FCC compliance.
•  Infrequently used radio links should be tested regularly to protect against undetected 

interference or fault.

•  A general knowledge of radio and its vagaries should be gained prior to acting as a 

wholesale distributor or dealer, and these facts should be communicated to the ultimate 
users.