JVC KENWOOD Corporation 33256 ユーザーズマニュアル

|

English

English

   

|

   

When "CALL" or "Call" is displayed, "(Calling party 
name)" or "(Phone number)" is also displayed.
Press the [AUDIO] button or one of [1] – [6] 
buttons.

•  You can set up the unit so that the incoming call is 

received after lapse of a predetermined time. For more 
details, see <Setting the Time Interval for Automatic 
Answer> (page 11).

•  Inserting a disc such as a CD will disconnect your call.
•  Setting the cell-phone in the private mode can disable 

the hands-free function.

•  When a call without caller ID arrives, "No Name No 

Number", "No Number", or "NO-NMBER" is displayed.

•  The name of the calling party is displayed if it has 

already been registered in the Phone Book.

•  You can also press the [ATT] button for at least 1 

second to disconnect a call. 

You can switch between the private mode 
(talking directly on the cell-phone) and the 
hands-free mode.

38]).

Talk modes are switched as follows:

"Private Talk"/ "Private"/ "PV TALK"

Private talk

"Handsfree Talk"/ "Handsfree"/ "HF TALK" Hands-free talk

•  Depending on the type of your cell-phone, switching 

to the private talk mode may select the source 
that was used before commencing the hands-free 
connection. If this happens, the source cannot 
be switched back to the hands-free talk mode by 
operating this unit. Operate your cell-phone to return 
to the hands-free talk mode.

You can adjust the voice volume during a call in 
progress.

•  The volume adjusted during the current call in 

progress will be effective for the next and subsequent 
calls.

•  Increasing the volume excessively is more likely 

to produce echo. If echo is produced, turn down 
the volume as low as possible. Echo increases in 
proportion to the volume. 

You can switch between the Phone Book and the 
Call List. 

Press the [DISP]/ [AUTO]/ [TI] button.
If the [DISP] button is not provided, press the 
[AUTO] or [TI] button.

Multi-function Key System
  Press the [AUTO]/ [TI] button.
Pressing this button toggles between the name 
list and the phone number list. 

You can scroll through the list of phone numbers 
or names. For the operation method, refer to 
<Text/Title Scroll> in the Instruction Manual that 
comes with the control unit.

•  With the control unit on which only a name is 

displayed during call termination or quick dialing, you 
can switch to the phone number display mode by 
performing the above operation.

•  Depending on the type of your control unit, the 

following restrictions are placed.
-  Up to 19 characters can be displayed.
-  The # letter cannot be displayed, or "

|" (all segments 

are lit) is displayed for #.

-  You cannot switch between display modes. 

You can clear the message displayed after 
disconnection of the cell-phone.

Press the [ATT] button for at least 1 second.
"Disconnect" or "DISCONNECT" disappears.

•  It may take some time before the disconnected cell-

phone is reconnected.

You can dial in five different ways.

Press the [ATT] button for at least 1 second.
"DIAL" or "N-DIAL" is displayed.

38]).

Pressing this knob toggles between the following 
dialing method selection modes:

Select the key function section.

"DIAL"/ 
"N-DIAL"

[1] ("DIAL") Dial by entering a phone number. 

(page 7)
Dial by using the quick dialing 
function. (page 7)

"INITIAL"/ 
"PH-BOOK1"

[2] 
("PHBK")*

Dial by searching for the initial in the 
Phone Book (page 8)

"PH.BOOK"/ 
"PH-BOOK2"

[2] 
("PHBK")*

Dial by searching the Phone Book in 
the alphabetical order. (page 8)

"OUT"/ 
"OUT-CALL"

[3] ("OUT-C") Dial by using the dialed call list. 

(page 8)

"IN"/ 
"IN-CALL"

[4] ("IN-C") Dial by using the received call list. 

(page 9)

•  To use the Phone Book, it must have been 

downloaded from the cell-phone. For more details, 
see <Downloading the Phone Book> (page 5).

•  The dialed call list and the received call list are the 

lists of calls originated from and terminated to this 
unit. They are not the ones stored in the cell-phone 
memory.

•  *  With the Multi-function Key System, pressing the [2] 

("PHBK") button switches between the Phone Book 
search methods.

¢]) button on the remote controller.

Press the [DIRECT] button on the remote 
controller.
"CALL" or "Call" is displayed.

4] button on the remote 

•  You can input max 32 digits.
•  Depending on the type of your control unit, "

|" (all 

segments are lit) is displayed for #.

You can dial by calling the phone number 
registered to the preset dial number list.

Select the "DIAL" or "N-DIAL" display.
Refer to <Selecting the Dialing Mode> (page 7).

preset dial number
Press the [1] – [3] button.
"Preset #" or "PRESET #" is displayed.

Select the key function section.

"DIAL #" is displayed.

38]) for at least 1 

second.
"CALL" or "Call" is displayed.

•  If the desired number is not registered to the preset 

dial number list, "No Name No Number", "No Number", 
or "NO-NUMBER" is displayed.

Function of remote control

You can make a call by entering a phone number.

Select the "DIAL" or "N-DIAL" display.
Refer to <Selecting the Dialing Mode> (page 7).