Lutron Electronics Company Inc 0075 ユーザーズマニュアル

Lutron Electronics Co., Inc.

7200 Suter Road Coopersburg, PA 18036-1299

P/N 040399 Rev. A  09/2013

®

Light does not respond 

to PicoR wireless control

• The dimmer/switch failed to pair with PicoR wireless control; see 

Set-Up.

• The dimmer/switch has already received and responded to a command or is already at the light setting the PicoR 

wireless control is sending.

• The PicoR wireless control is outside the 30 ft (9 m) operating range.

• The battery in the PicoR wireless control is low.

• The battery in the PicoR wireless control is installed incorrectly.

When in set-up mode 

the LEDs on the dimmer/

switch flash when trying 

to setup with the PicoR 

wireless control or sensor.

• The maximum number of PicoR wireless controls or sensors have been paired with the dimmer/switch. More PicoR 

wireless controls or sensors can not be added. See 

Un-pairing a PicoR Wireless Control.

Nightlight LED on the 

PicoR wireless control is 

not illuminated

•  The battery in the PicoR wireless control is installed incorrectly.

•  The battery in the PicoR wireless control is low and needs to be replaced.

WirelessR systems only. If you are using your PicoR wireless 

control with any other LutronR system, please refer to the system 

www.lutron.com/pico 

2.  The PicoR wireless control uses one (1) CR2032 battery. DO NOT 

use rechargeable batteries. Using improper batteries could damage 

the PicoR wireless control. 

DO NOT dispose of the battery in normal 

household waste. Please recycle it by taking it to a proper battery 

disposal facility, or contact your local waste disposal provider regarding 

local restrictions on the disposal or recycling of batteries. 

in serious injury or death. DO NOT recharge, disassemble, 

crush, puncture, heat above 212 °F (100 °C) or incinerate the 

battery. The battery in this device contains Perchlorate  

Material - special handling may apply. For more information 

visit www.dtsc.ca.gov/hazardouswaste/perchlorate

3.  The PicoR wireless control must be paired with dimmer(s) /switch(es) 

before it can communicate.

4.  Up to 10 PicoR wireless controls can be configured to work together in 

a Maestro WirelessR system.

5.  The range of the PicoR wireless control is 30 ft (9 m). Performance is 

highly dependent on a variety of complex factors such as:

   )

 Distance between system components

   )

 Geometry of the building structure

   )

 Construction of walls separating system components

   )

 Electrical equipment located near system components

6.  Clean PicoR wireless control with a soft damp cloth only. DO 

NOT use any chemical cleaners.

7. DO NOT paint the PicoR wireless control.
8.  DO NOT mount the PicoR wireless control to a metal surface.

®

  Installing the Battery in a PicoR Wireless Control 

1. Place a flathead screwdriver into 

the slot at the bottom of the PicoR 

wireless control. Twist to open.  

DO NOT press buttons without 

back enclosure on.

2. Slide a new battery underneath the 

contact strap, with the (-) terminal 

toward the front of the PicoR 

wireless control.

3. Replace the back enclosure.
4. If installing a new battery, proceed to Set-up. If replacing the battery, 

confirm proper installation by turning the receiving device on and off 

using the PicoR wireless control. 

 

(for Maestro WirelessR systems only)

  To communicate with other systems or devices, including 

Radio RAR 2, QS sensor module (QSM), QuantumR, and HomeWorksR 

QS, refer to the system setup guides. See www.lutron.com/pico for 

more information.

 Important: Set up a PicoR wireless control to a dimmer/switch before 

use.

1. Press and hold the dimmer/switch tap button (Figure 1) for 

approximately 6 seconds. Once the LED(s) start to blink slowly, 

release the tap button.

2.  Press and hold the OFF button on the PicoR wireless control  

(Figure 2) for approximately 6 seconds.

3.  Once the dimmer/switch pairs with the PicoR wireless control, the 

LED(s) on the dimmer/switch and the load will flash 3 times and it will 

exit Set-Up mode.

4.  Repeat steps 1 to 3 to pair multiple PicoR wireless controls with a 

single dimmer / switch. Repeat steps 1 to 3 to pair a single PicoR 

wireless control with  multiple  dimmers / switches.

5.  Pressing the Preset button (-3BRL model only) on a PicoR wireless 

control will cause all dimmers to go to the favorite light settings. 

Switches can be configured to turn ON or OFF. To save a favorite 

light setting, adjust all the dimmers/switches controlled by a PicoR 

wireless control to the desired light setting. Then press and hold the 

Preset button on the PicoR wireless control for 6 seconds until all 

LEDs on the dimmers/switches flash several times. 

3 V-  10 mA

Lutron, ), HomeWorks, Pico, Maestro Wireless, RadioRA, and Quantum are registered trademarks and RadioRA 2 is a trademark of Lutron Electronics Co., Inc.

© 2013 Lutron Electronics Co., Inc.

For a complete listing of PicoR wireless 

mounting accessories, please visit 

www.lutron.com/pico

Preset Button (-3BRL model only)

Tap Once: Devices go to preset levels. 

Press and Hold: To save new preset 

level or position, press and hold for 

6 seconds.

Lights dim to off. 

English

For questions concerning the installation or operation of this product, call the 

Lutron Technical Support Center. Please provide exact model number when 

calling.
TEL  +1.610.282.3800
FAX  +1.610.282.1243
Toll Free  1.888.LUTRON1
USA, Canada, Caribbean  1.800.523.9466
Mexico  +1.888.235.2910
Central/South America  +1.610.282.6701

  If multiple wireless dimmers/switches are paired with the same PicoR 

wireless control, they will perform as follows: 

) 

  Pressing the ON button on the PicoR wireless control will cause all 

dimmers/switches to turn ON fully.

) 

  Pressing the OFF button on the PicoR wireless control will cause all 

dimmers/switches to turn OFF completely.

) 

  Pressing the Raise button (-3BRL model only) on a PicoR wireless 

control will cause all dimmers to turn ON and gradually increase in 

intensity.

) 

  Pressing the Lower button (-3BRL model only) on a PicoR wireless 

control will cause all dimmers to gradually decrease in intensity. The 

dimmers will not turn off and will remain at low-end.

) 

  Pressing the Preset button (-3BRL model only) on a PicoR wireless 

control will cause all dimmers to return to the favorite light settings. 

Switches can be configured to go to ON or OFF. (See Step 5 in Set-Up)

  Un-pairing a PicoR Wireless Control

(for Maestro WirelessR systems only)

  To un-pair a previously paired PicoR wireless control from your 

system, tap the OFF button (Figure 2) on the PicoR wireless control 

three times, on the third tap hold for 6 seconds and then tap three 

more times. This will remove all dimmers/switches it was previously 

paired with.

Lights brighten to full intensity. 

Raise Button (-3BRL model only)

Lights increase in intensity.

Lower Button (-3BRL model only)

Lights decrease in intensity.

Glows a soft green color.

Flashes to indicate a button press or 

when unit is in programming mode.

United Kingdom
Lutron EA Ltd.
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
Technical Support:  
+44.(0)20.7680.4481
Freephone: 0800.282.107
www.lutron.com/europe

Singapore
TEL  +65.6220.4666
FAX  +65.6220.4333

Asia Technical Hotlines
Northern China  10.800.712.1536
Southern China  10.800.120.1536
Hong Kong  800.901.849
India  +91.11.4051.4300
Indonesia  001.803.011.3994
Japan  +81.3.5575.8411
Macau  0800.401
Singapore  800.120.4491
Taiwan  00.801.137.737
Thailand  001.800.120.665853
Other countries  +65.6220.4666

http://www.lutron.com/en-US/ 
Products/Documents/Components/ 
PicoWirelessController/FCC.html