JVC KENWOOD Corporation 422401 ユーザーズマニュアル

◆

 This repeater is intended for use as a fixed base station with

the antenna located outdoors on the rooftop or on an antenna 

tower.

◆

 This repeater is designed for a 13.6 V DC power source!

Never use a 24 V DC or higher source to power the repeater.

◆

 Use only the supplied DC cord.

◆

 Do not remove the ferrite core attached to the DC cord. Doing

so may cause interference with radio communications.

The following unpacking information is for use by your Kenwood 

dealer, an authorized Kenwood service center, or the factory.

Carefully unpack the repeater. We recommend that you identify

the items listed in the following table before discarding the

packing material. If any items are missing or have been damaged

during shipment, file a claim with the carrier immediately.

Hardware fixture

J21-8559-XX

1

Front glass

B10-2635-XX

1

Name plates

B11-1259-XX

1

Cushion

G13-1801-XX

4

Cushion

G13-1802-XX

4

Foot

J02-0475-XX

2

Foot

J02-0492-XX

2

Grommet

J59-0302-XX

2

Handle

K01-0418-XX

1

Screws

N30-4006-XX

2

Screws

N35-3006-XX

5

DC cord

E30-3427-XX

1

Lead wire with connector (15 pin)

E31-3228-XX

1

Fuse

F05-1537-XX

1

Instruction Manual

B62-2199-XX

1

To install the handles onto the front panel of the repeater, align 

the handles with the holes on the front panel, then secure the

handles using the supplied screws.

Please consult your dealer for installing the repeater and 

antenna.

Connect an optional KMC-30, KMC-35, KMC-27A, KMC-27B, 

or KMC-9C Kenwood microphone to the MIC jack on the front

panel.

◆

 Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆

 Illegal operation is punishable by fine and/or imprisonment.

◆

 Refer service to qualified technicians only.

FCC WARNING
This equipment generates or uses radio frequency energy. Changes

or modifications to this equipment may cause harmful interference

unless the modifications are expressly approved in the instruction

manual. The user could lose the authority to operate this equipment if

an unauthorized change or modification is made.

THE FCC
This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency 

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur

in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

  • 

Reorient or relocate the receiving antenna.

  • 

Increase the separation between the equipment and receiver.

  • 

Connect the equipment to an outlet on a circuit different from that to 

which the receiver is connected.

  • 

Consult the dealer for technical assistance.

We are grateful you purchased this Kenwood repeater. We

believe this easy-to-program repeater will be highly effective in

your communications system, and will keep personnel operating

at peak efficiency.

•  Do not expose the unit to rain or moisture; to prevent fire or

electric shock.

•  Do not open the unit under any circumstances; to avoid risk

of electric shock.

•  Do not expose the unit to long periods of direct sunlight, nor

place it close to heating appliances.

•  Do not place the unit in excessively dusty and/or humid

areas, nor on unstable surfaces.

•  If you detect an abnormal odor or smoke coming from the

unit, disconnect the power from the unit immediately. Contact

your Kenwood service center or dealer.

The AMBE+2

TM

voice coding Technology embodied in this product

is protected by intellectual property rights including patent rights,

copyrights and trade secrets of Digital Voice Systems, Inc. This voice

coding Technology is licensed solely for use within this Communications

Equipment. The user of this Technology is explicitly prohibited from

attempting to extract, remove, decompile, reverse engineer, or

disassemble the Object Code, or in any other way convert the Object

Code into a human-readable form. U.S. Patent Nos. #5,870,405,

#5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050,

#5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084

and #5,195,166.

The title to and ownership of copyrights for firmware embedded in

Kenwood product memories are reserved for Kenwood Corporation.