JVC KENWOOD Corporation 431200 ユーザーズマニュアル

1

Note:  The following instructions are for use by your KENWOOD dealer, an authorized KENWOOD 
service facility, or the factory.

Carefully unpack the transceiver.  We recommend that you identify the items listed below 
before discarding the packing material.  If any items are missing or have been damaged 
during shipment, file a claim with the carrier immediately.

DC power cable (with fuses). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
• 

15 A fuse  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mounting Bracket  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screw set
• 

5 x 16 mm self-tapping screw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 4

• 

Hex-headed screw with washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

• 

Spring washer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

• 

Flat washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Microphone (with cable)
• 

KMC-35  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Microphone hanger (with 4 x 16 mm self-tapping screws) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Instruction manual  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Various electronic equipment in your vehicle may malfunction if they are not properly protected 
from the radio frequency energy which is present while transmitting.  Typical examples include 
electronic fuel injection, anti-skid braking, and cruise control.  If your vehicle contains such 
equipment, consult the dealer for the make of vehicle and enlist his/her aid in determining if they 
will perform normally while transmitting.

■  Power Cable Connection

The transceiver operates in 12 V negative ground systems only!  Check the battery polarity and 
voltage of the vehicle before installing the transceiver.

1  Check for an existing hole, conveniently located in the firewall, where the power 

cable can be passed through.
•  If no hole exists, use a circle cutter to drill a hole, then install a rubber grommet.

2  Run the power cable through the firewall and into the engine compartment.

3  Connect the red lead to the positive (+) battery terminal and the black lead to the 

negative (–) battery terminal.
•  Place the fuse as close to the battery as possible.

4  Coil the surplus cable and secure it with a retaining band.