Crestron Electronics Inc CLWI-KPLEX ユーザーズマニュアル
Crestron Electronics, Inc. Installation Guide - DOC. 7244A
15 Volvo Drive Rockleigh, NJ 07647
(2031641)
Tel: 888.CRESTRON
09.13
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Further Inquiries
To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at
1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of
Crestron worldwide offices at www.crestron.com/offices.
To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp.
First-time users must establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of the CLWI-KPLEX-BATT,
additional information may be made available as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical documentation revision.
Check the Crestron Web site periodically for manual update availability and its relevance. Updates are identified as
Check the Crestron Web site periodically for manual update availability and its relevance. Updates are identified as
an “Addendum” in the Download column.
WARNING: To avoid fire, shock, or death; turn off power at circuit breaker or fuse and test that power is off before
wiring!
NOTES: Observe the following points.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• This product should be installed by a qualified electrician
• This product should be installed by a qualified electrician
Crestron CLWI-KPLEX-BATT
In-Wall Wireless Lighting Keypad, Battery Powered
Installation Guide
As of the date of manufacture, the CLWI-KPLEX-BATT have been tested and found to comply with specifications for
CE marking and standards per EMC and Radiocommunications Compliance Labelling.
Regulatory Compliance
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cuase harmful interference and (2) this device must accept any interference received, including
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cuase harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
(Continued on following page)
INTRODUCTION
The CLWI-KPLEX-BATT is a companion keypad for Crestron
®
CLWI dimmers and switches,
sharing the exact same aesthetics. It provides lighting and audio control from more than one
location around the home or office using infiNET EX
®
technology. Recall scenes, dim up and
down, and adjust volume using the customizable button layout.
Specifications
Specifications for the CLWI-KPLEX-BATT are listed in the following table.
CLWI-KPLEX-BATT Specifications
Specifications
Specifications for the CLWI-KPLEX-BATT are listed in the following table.
CLWI-KPLEX-BATT Specifications
OPERATION
The device receives firmware upgrades via infiNET EX over-the-air firmware upgrades. Refer
to the Crestron Toolbox™ help file for details.
ASSIGN BUTTON FUNCTIONS
The CLWI-KPLEX-BATT button functions are based on the control system’s program. Refer
to the Crestron Studio™ or SIMPL Windows help file for details.
3. Insert the new button assemblies onto the device by pressing them into the device. It
might be necessary to squeeze the sides of the button assembly to allow for easier
assembly.
Install Button Assembly
Install Button Assembly
CHANGE BUTTON ASSEMBLIES
Follow the procedure below if the button assemblies need to be changed or replaced.
1. Squeeze the sides of the button assembly near the center of the device or, for two or
1. Squeeze the sides of the button assembly near the center of the device or, for two or
more button assemblies, press on one side of the button assembly.
2. Remove the button assembly by carefully pulling the button assembly off of the device.
For two or more button assemblies, remove the second button in the same manner.
Refer to the illustrations that follow.
Remove Button Assembly
MOUNTING
The CLWI-KPLEX-BATT can be mounted using double-sided tape or mounting screws (not
supplied). Refer to the procedures below for mounting instructions.
Stick-On Surface Mounting
The CLWI-KPLEX-BATT can be mounted to the wall using double-sided tape. Refer to the
Stick-On Surface Mounting
The CLWI-KPLEX-BATT can be mounted to the wall using double-sided tape. Refer to the
following procedure for instructions.
1. Remove the release liner on one side of the double-sided tape.
2. Carefully lay the exposed adhesive side of the double-sided tape flat across the rear
1. Remove the release liner on one side of the double-sided tape.
2. Carefully lay the exposed adhesive side of the double-sided tape flat across the rear
surface of the keypad and gently press down on the double-sided tape to ensure
adhesion.
3. Remove the second release liner on the double-sided tape.
4. Firmly press the rear surface of the keypad flat against the wall to ensure adhesion.
Stick-On Surface Mounting
4. Firmly press the rear surface of the keypad flat against the wall to ensure adhesion.
Stick-On Surface Mounting
Permanent Mounting
The CLWI-KPLEX-BATT can be mounted to a round or square electrical box using four
The CLWI-KPLEX-BATT can be mounted to a round or square electrical box using four
mounting screws (not supplied) or directly to a flat surface using screws appropriate for the
mounting scenario (not supplied). Refer to the following illustration for a typical permanent
mount scenario.
Permanent Surface Mounting
Permanent Surface Mounting
Secure to the electrical box or flat
surface using screws appropriate for
the mounting scenario (not supplied).
Secure to the mounting surface
using the double-sided tape
attached to the rear of the device.
SPECIFICATION
DETAILS
Power Requirements
3 Volts ac, CR2450 battery
Wireless
RF Transceiver
2-way RF, 2.4 GHz ISM Channels 11 to 26
(2400 to 2483.5 MHz), IEEE 802.15.4 compliant
Range (Typical)
Subject to site-specific conditions;
Range is increased by adding additional devices or
wireless expander
Gateway
Requires an infiNET EX gateway (sold separately)
Environmental
Temperature
0° to 40° C (32° to 104° F)
Humidity
10% to 90% RH (non-condensing)
Enclosure
Mounts to surface, requires faceplate (not included)
Dimensions
Height
73 mm (2.85 in)
Width
73 mm (2.85 in)
Depth
20 mm (0.76 in) including front face with buttons
Weight
55 g (2 oz)