Crestron Electronics Inc CWD1011 ユーザーズマニュアル
CLW-DIM1RF, DIMS1RF, & SLVD1RF(W/A/B)
Introduction
Specifications
Following are specifications for the -DIM1RF,
-DIMS1RF, and -SLVD1RF.
-DIMS1RF, and -SLVD1RF.
Features and Functions
The CLW-DIM1RF (-DIM1RF) is a stand-alone wall box
dimmer that can also act as a wireless Cresnet
dimmer that can also act as a wireless Cresnet
®
device
that reports to a Crestron
®
control processor via a wireless
gateway such as the Crestron C2N-MNETGW. The CLW
-DIM1RF has two preset lighting levels that can be
adjusted (refer to note below). The CLW-DIM1RF
features an internal antenna for communication with
Crestron wireless switches using the 2.4 GHz ISM
frequency range.
-DIM1RF has two preset lighting levels that can be
adjusted (refer to note below). The CLW-DIM1RF
features an internal antenna for communication with
Crestron wireless switches using the 2.4 GHz ISM
frequency range.
CLW-DIM1RF, CLW-DIMS1RF, & CLS-SLVD1RF
Specifications
Specifications
SPECIFICATION DETAILS
Power Requirements
Line Power, 120 VAC, 60 Hz
Operating Frequency
2.4 GHz ISM
Default RF ID
-DIM1RF: 00
-DIMS1RF: 00
-DIMS1RF: 00
Switch Type
Dimmer
Load Type
Incandescent, Tungsten-Halogen,
Magnetic Low Voltage
Magnetic Low Voltage
2-Series Control System
Update File
Update File
1,2
Version 3.117 or later
Load Ratings
3
Incandescent/Tungsten
Halogen
-DIM1RF: 1000W
-DIMS1RF: 1000W
-SLVD1RF: N/A
-DIMS1RF: 1000W
-SLVD1RF: N/A
Magnetic Low Voltage
4
-DIM1RF:
1000VA/750W
-DIMS1RF: 1000VA/750W
-SLVD1RF: N/A
-SLVD1RF: N/A
Operating Temperature
and Humidity
and Humidity
32°F to 104°F (0°C to 40°C)
10 to 90% Relative Humidity
(Non-Condensing)
10 to 90% Relative Humidity
(Non-Condensing)
Dimensions and Weight
-DIM1RF and -DIMS1RF:
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.88 in (4.77 cm)
Weight: 4.9 oz (0.67 kg)
-SLVD1RF:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.88 in (4.77 cm)
Weight: 3.6 oz (0.50 kg)
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.88 in (4.77 cm)
Weight: 4.9 oz (0.67 kg)
-SLVD1RF:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.88 in (4.77 cm)
Weight: 3.6 oz (0.50 kg)
NOTE: The two preset levels are noted as Preset 1-High
and Preset 1- Low. “Preset 1-High” is usually used for
turning lights on to full brightness while preset “Preset 1-
Low” is usually used for turning the lights off. Although
“Preset 1-High” and “Preset 1-Low” are usually used for
“On” and “Off” respectively, the light level for each
preset can be customized by the user. Refer to “Operating
Button and Switch” on page 4 for more information on
customizing light levels.
and Preset 1- Low. “Preset 1-High” is usually used for
turning lights on to full brightness while preset “Preset 1-
Low” is usually used for turning the lights off. Although
“Preset 1-High” and “Preset 1-Low” are usually used for
“On” and “Off” respectively, the light level for each
preset can be customized by the user. Refer to “Operating
Button and Switch” on page 4 for more information on
customizing light levels.
The CLW-DIM1RF features a three-position mode
selection switch. Refer to “Operating Button and Switch”
on page 5 for more information. In the absence of Cresnet
communications, the dimmer can still be used to control
lighting.
selection switch. Refer to “Operating Button and Switch”
on page 5 for more information. In the absence of Cresnet
communications, the dimmer can still be used to control
lighting.
The CLW-DIMS1RF (-DIMS1RF) is similar to the -
DIM1RF with the added capability of working with a
slave unit (CLW-SLVD1RF) in a multi-switch / single
circuit application.
DIM1RF with the added capability of working with a
slave unit (CLW-SLVD1RF) in a multi-switch / single
circuit application.
The CLW-SLVD1RF (-SLVD1RF) is a slave unit that
when used in conjunction with the -DIMS1RF acts as an
additional dimmer control point in a multi-dimmer /
single circuit application. It does not connect to a Cresnet
system and cannot be used without a -DIMS1RF. The
-SLVD1RF does not have a mode selection switch and is
not programmable. It emulates the operation of the
-DIMS1RF to which it is connected.
when used in conjunction with the -DIMS1RF acts as an
additional dimmer control point in a multi-dimmer /
single circuit application. It does not connect to a Cresnet
system and cannot be used without a -DIMS1RF. The
-SLVD1RF does not have a mode selection switch and is
not programmable. It emulates the operation of the
-DIMS1RF to which it is connected.
1.
The latest software versions can be obtained from the Crestron
website. Refer to the NOTE following these footnotes.
website. Refer to the NOTE following these footnotes.
2.
Crestron 2-Series control systems include the AV2 and PRO2.
Consult the latest Crestron Product Catalog for a complete list of
2-Series control systems.
Consult the latest Crestron Product Catalog for a complete list of
2-Series control systems.
3.
Refer to Derating Charts for Multigang Installations on page 3.
The -DIM1RF, -DIMS1RF, and -SLVD1RF are available
in white, almond, and black. White units are designated
by part numbers ending in “W”. Almond units are
designated by part numbers ending in “A”. Black units are
designated by part numbers ending in “B”. Each dimmer
can be covered with a decorative faceplate (not supplied).
in white, almond, and black. White units are designated
by part numbers ending in “W”. Almond units are
designated by part numbers ending in “A”. Black units are
designated by part numbers ending in “B”. Each dimmer
can be covered with a decorative faceplate (not supplied).
4.
VA ratings are for input power to the transformer. If you do not
know the input power requirement of the transformer, use the
bulb’s wattage rating to determine proper rating.
know the input power requirement of the transformer, use the
bulb’s wattage rating to determine proper rating.
NOTE: Crestron software and any files on the website
are for Authorized Crestron dealers and Crestron
Authorized Independent Programmers (CAIP) only. New
users may be required to register to obtain access to
certain areas of the site (including the FTP site).
are for Authorized Crestron dealers and Crestron
Authorized Independent Programmers (CAIP) only. New
users may be required to register to obtain access to
certain areas of the site (including the FTP site).
Crestron Electronics, Inc.
Installation Guide – DOC. 6292
15 Volvo Drive Rockleigh, NJ 07647
02.05
Tel: 888.CRESTRON
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.