Crestron Electronics Inc CWD1011 ユーザーズマニュアル
CLW-DIM1RF, DIMS1RF, & SLVD1RF(W/A/B)
Wiring Diagram for CLW-DIM1RF (L) / CLW-DIMS1RF (R)
Installation
Hot
Neutral
Load
RED
BLACK
WHITE
BLUE
Ground
GREEN
LINE
120VAC
60Hz
60Hz
120VAC
LINE
GREEN
Ground
WHITE
BLACK
RED
Load
Neutral
Hot
NOTE: The -DIMS1RF must be installed in the same
wallbox that contains the connections to the load.
wallbox that contains the connections to the load.
NOTE: The -DIM1RF, -DIMS1RF, and -SLVD1RF
require a neutral wire for operation. If no neutral is
present, contact a licensed electrician for installation or
contact Crestron Customer Service for alternative wiring
options.
require a neutral wire for operation. If no neutral is
present, contact a licensed electrician for installation or
contact Crestron Customer Service for alternative wiring
options.
WARNING: Turn off power at the circuit breaker.
Installing with power on can result in serious personal
injury and damage to the device.
Installing with power on can result in serious personal
injury and damage to the device.
NOTE: The RED (Load) and BLACK (Hot) wires are
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG.
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG.
NOTE: New installations should be checked for short
circuits prior to installing the -DIM1RF, -DIMS1RF, or
-SLVD1RF. With power off, close the circuit and restore
power. If the lights do not work or a breaker trips, check
and correct the wiring or fixture (if necessary). Install the
-DIM1RF, -DIMS1RF, or -SLVD1RF only when the
short is no longer present. The warranty is void if the
-DIM1RF, -DIMS1RF, or -SLVD1RF is installed and
operated with a shorted load.
circuits prior to installing the -DIM1RF, -DIMS1RF, or
-SLVD1RF. With power off, close the circuit and restore
power. If the lights do not work or a breaker trips, check
and correct the wiring or fixture (if necessary). Install the
-DIM1RF, -DIMS1RF, or -SLVD1RF only when the
short is no longer present. The warranty is void if the
-DIM1RF, -DIMS1RF, or -SLVD1RF is installed and
operated with a shorted load.
CLW-DIMS1RF with CLW-SLVD1RF
Wiring
Wiring
NOTE: The -DIMS1RF must be installed in the same
wallbox that contains the connections to the load.
wallbox that contains the connections to the load.
The following wiring diagram illustrates installation of
the -DIMS1RF with multiple -SLVD1RFs.
the -DIMS1RF with multiple -SLVD1RFs.
1. Turn power off at the circuit breaker.
2. If installing multiple dimmers (-DIM1RF or
-DIMS1RF), note the serial number on each
device and make sure they are being installed in
the proper location.
device and make sure they are being installed in
the proper location.
Wiring Diagram of CLW-DIMS1RF with multiple CLW-
SLVD1RFs
SLVD1RFs
Hot
Neutral
Load
RED
CLW-DIMS1RF
BLACK
WHITE
CLW-SLVD1RF
BLUE
BLACK
BLUE
Ground
Ground
GREEN
GREEN
LINE
120VAC
60Hz
WHITE
Ground
GREEN
BLACK
BLUE
CLW-SLVD1RF
WHITE
3. Wire the device for the appropriate application.
Choose either “CLW-DIM1RF / CLW-
DIMS1RF Wiring” or “CLW-DIMS1RF with
CLW-SLVD1RF Wiring”, shown on this page
and the following page.
DIMS1RF Wiring” or “CLW-DIMS1RF with
CLW-SLVD1RF Wiring”, shown on this page
and the following page.
NOTE: Alternative wiring methods can be obtained from
the Dealer/Tech Resources | Design Center section of the
Crestron website (http://www.crestron.com/dealer-
tech_resources/design_center/hot_design_tips_and_
diagrams/tech_sales_tips/).
the Dealer/Tech Resources | Design Center section of the
Crestron website (http://www.crestron.com/dealer-
tech_resources/design_center/hot_design_tips_and_
diagrams/tech_sales_tips/).
NOTE: Do not connect the BLUE (Slave) wire to the
Black (Hot) or RED (Load) wires.
Black (Hot) or RED (Load) wires.
CLW-DIM1RF / CLW-DIMS1RF Wiring
NOTE: The RED (Load) and BLACK (Hot) wires are
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG.
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG.
NOTE: The -DIM1RF and -DIMS1RF require a neutral
wire for operation. If no neutral is present, contact a
licensed electrician for installation or contact Crestron
customer service for alternative wiring options.
wire for operation. If no neutral is present, contact a
licensed electrician for installation or contact Crestron
customer service for alternative wiring options.
NOTE: If a -DIMS1RF is installed without a
-SLVD1RF, the BLUE lead (Slave) should be capped.
-SLVD1RF, the BLUE lead (Slave) should be capped.
The following wiring diagram illustrates installation of
the -DIM1RF or -DIMS1RF.
the -DIM1RF or -DIMS1RF.
4. Push all Class 1 power wires back into the
wallbox and fasten the device to the wallbox
with the provided screws.
with the provided screws.
5. Attach decorative faceplate.
6. Restore
power.
4
• Stand Alone Wall Box Dimmer : CLW-DIM1RF, DIMS1RF, & SLVD1RF
Installation Guide – DOC. 6292