Microwave Radio Communications LLC L32112GAMP ユーザーズマニュアル
www.vislink.com
© 2011 Vislink Group. All rights reserved. All other products or services referenced herein are
identified by the trademarks or service marks of their respective companies or organizations.
Note: Vislink reserves the right to change specifications without notice. Please contact your
representative to confirm current specifications. Document 10 / 7 / 2011
Specifications
Electrical
At 20±5°C ambient
Parameter
Conditions
Min
Typ
Max
Units
Comment
Frequency Range
L3211-2027
2000
–
2700
MHz
L3211-6475
6400
-
7500
MHz
Does not include LDPD
RF Output Power
ALC Mode
+28 (0.63)
28.75(0.75)
+30 (1.0)
dBm (W)
RF Input Power Range
ALC Mode
+10 (10)
–
+24 (250)
dBm (mW)
Gain
Fixed Gain Mode
10
–
15
dB
Spectral Regrowth
Adjacent Channel
–
–
-40
dBc
EN 302 064-1 §7.3.4
Alternate Channe
–
–
-46
Spurious
25MHz – 1GHz
–
–
0.25(-36)
nW(dBm)
EN 302 064-1 §7.4.6
1GHz – 27GHz
–
–
1(-30)
Return Loss
–
10
–
dB
RF Input
Damage Level
CW
+27 (0.5)
dBm (W)
Pulsed
+36 (4)
Static Protection
Direct Discharge
8
kV
IEC61000-4-2
Air Discharge
15
Temperature Rise
Above Ambient
32
ºC
IEC60417-5041
Supply Voltage
9
28
V
Power Consumption
RF OFF
7.5
W
RF ON
14
W
Compliance
Standard
Class/Category
Version
ETSI EN 302 064-1
Category 1
V1.1.2
ETSI EN 301 489-28
Class B
V1.1.1
Environmental
Operating Temperature
(Portable Equipment)
• -10°C to +50°C
Storage Temperature
• -20°C to +80°C
Humidity
• 95%
• Non-Condensing
IP Rating
• 54
Mechanical
RF/DC Input Connector
• 50Ω N Type (M)
RF Output Connector
• 50Ω N Type (F)
Power Connector
• 6-Pin Lemo Socket
Phantom Power
• Applied to RF Input Connector
Weight
• 0.32Kg
Length
• 106mm (inc. connectors)
Diameter
• 62mm
Status Indicator
• Green (DC Power/ALC OK)
• Orange (DC Power OK/Fixed Gain)
Power Connector 6-Pin Lemo Socket
L3211 Socket
• EEG.OB.306 CLV
Mating Plug
• FGG.0B.306 CLA (straight)
• FHG.0B.306 CLA (right-angle)
Pin Out
• 1 & 2: GND, 3 & 4: +VE, 5 & 6: NC
Note: When operating the barrel booster
in the ‘Fixed Gain’ mode the RF output
power is no longer controlled by the
barrel booster’s ALC and therefore it is the
operator’s responsibility to ensure that
the RF drive into the barrel booster is at an
appropriate level not to cause over-drive
or damage and to maintain regulatory
compliance.
Hot surface, do not touch barrel booster
heat sink surface during operation.
The barrel booster is supplied with 2 complimentary
power cables from the options listed below
PN:9003434
Barrel Booster ALC Power Cable (Lemo straight)
Pn:9003435
Barrel Booster ALC Power Cable (IDX D-TAP)
Pn:9003437
Barrel Booster ALC Power Cable (Anton Bauer P-TAP)
Pn:9003438
Barrel Booster ALC Power Cable (Lemo right-angle)