Rosslare Enterprises Ltd KE-30G ユーザーズマニュアル
2
0706-0960254+00
4. Tamper
The KE-30 is secured to the wall with a screw (see Mounting
the KE-30). Tamper control is implemented via a knock-out
hole as soon as the KE-30 has been installed. Any attempt to
tamper with the system will set off an alarm.
Figure 4: Tamper Knock-Out
5. Utilizing the KE-30 Wireless keypad
The KE-30 functions as both an Arming/Disarming unit and as
a Status Viewing unit.
5.1 Arm/Disarm and Basic Operations
Below are instructions on how to arm the system using the
various options.
Basic Arming Using the keypad
•
Press the ARM AWAY key, and enter the user code. The
system will beep, and the ARM AWAY LED indicator will
flash.
•
Press the ARM HOME key, and enter the user code. The
system will beep, and the ARM HOME LED indicator will
flash.
•
Press the DISARM key, and enter the user code. The
DISARM LED indicator will flash.
The QUICK AWAY and QUICK HOME functions:
•
Press the AWAY button for 2 seconds. The system will
beep, and will be Armed AWAY.
•
Press the HOME button for 2 seconds. The system will
beep, and will be Armed HOME.
Emergency Alarm Activation:
•
Press on 1 and 3 simultaneously for 3 seconds to activate
the emergency alarm.
5.2 Status Viewing
Note: The ARM HOME LED indicator, the ARM AWAY LED
indicator, and the DISARM LED indicator flash, but they do
not remain on continuously.
The KE-30 indicates a panel's status by flashing the relevant
The KE-30 indicates a panel's status by flashing the relevant
LED indicator, and displays one of the following statuses:
•
Armed Away
•
Armed Home
•
Disarmed
•
In Memory and Trouble
•
By-pass
When a new KE-30 unit is turned on, a flashing TROUBLE LED
indicator indicates that the unit must be enrolled. Once it
has been enrolled, the Disarm LED indicator will flash.
If the system is experiencing trouble, the TROUBLE LED
If the system is experiencing trouble, the TROUBLE LED
indicator (!) will flash.
If there is an Alarm in Memory in the System, the ALARM LED
If there is an Alarm in Memory in the System, the ALARM LED
indicator (M) will flash.
If the System is by-passed, the BYPASS LED indicator (Z) will
If the System is by-passed, the BYPASS LED indicator (Z) will
flash.
5.3 RFID Function
Note: The RFID function is deactivated by default, since if it is
activated, battery life will be significantly shortened.
Enabling the RFID Function:
Press both on the * key and the # key for 3 seconds until the
system beeps twice.
After the system beeps twice, press 1, and then press #.
When the RFID is activated, the system will beep once.
After the system beeps twice, press 1, and then press #.
When the RFID is activated, the system will beep once.
Cancelling the RFID function:
Press both on the * key and the # key for 3 seconds until the
system beeps twice.
After the system beeps twice, press 0, and then press #.
The RFID is now deactivated.
After the system beeps twice, press 0, and then press #.
The RFID is now deactivated.
Enrolling proximity cards:
Please refer to the Proximity Card Enrolling section of the
HomeLogiX wireless panel manual or refer to any Rosslare
wireless panel manual that supports the relevant proximity
cards.
Using a Proximity Card to ARM or DISARM the System:
Note: First activate the RFID function.
Press on the Away, Home, or Disarm button. then place the
Using a Proximity Card to ARM or DISARM the System:
Note: First activate the RFID function.
Press on the Away, Home, or Disarm button. then place the
card directly above the keypad. The system will activate the
desired function (Arm Away/Home or Disarm).
Caution: Changes or modifications to this equipment
not expressly approved by the party responsible for
compliance (Rosslare Ltd.) could void the user’s
authority to operate the equipment.