Visonic Inc. DISCOVERYQDMCW ユーザーズマニュアル
DE3633
1
DISCOVERY QUAD
MCW
MCW
Wireless PowerCode Quad PIR Detector
Installation Instructions
1. FEATURES
•
Employs a real quad element low-noise pyroelectric sensor
•
Includes a fully supervised PowerCode transmitter
•
Patented sophisticated motion analysis algorithm - True Motion
Recognition (TMR™)
Recognition (TMR™)
•
Two-position vertical adjustment for coverage pattern
•
Integral swivel bracket for wall or ceiling installation
•
Programmable motion event counter - ON or OFF (default)
•
Front and back tamper switches for improved tamper protection
•
Full stabilization achieved 30 seconds after power up
•
After detection, the detector disables itself to save battery
power. It reverts to the ready state if there is no subsequent
detection throughout the following 2-minute period
power. It reverts to the ready state if there is no subsequent
detection throughout the following 2-minute period
•
Automatic termination of
walk-test after 15 minutes
•
Low current consumption
•
Microprocessor-controlled
temperature compensation
temperature compensation
•
Sealed chamber protects the
optical system
optical system
•
White light protection
•
Elegantly styled, sturdy case
•
Keyhole-shaped slot for
easy removal of PCB
easy removal of PCB
Figure 1. External View
2. SPECIFICATIONS
OPTICAL
Detector Type: Quad element low-noise pyroelectric sensor.
Detection Pattern: 90
Detector Type: Quad element low-noise pyroelectric sensor.
Detection Pattern: 90
°
wide angle lens with 19 quad zones in 3
detection
layers.
Max. coverage is 15 x 15 m (50 x 50 ft).
Adjustment: 2-position vertical adjustment scale: FAR and NEAR.
Figure 2. Coverage Pattern
ELECTRICAL
Internal Battery: 3
Internal Battery: 3
V Lithium battery, Panasonic CR-2 or
equivalent
Nominal Battery Capacity: 750 mAh
Standby Current Drain: 0.015 mA
Transmit Current Drain: 20 mA (including LED)
Battery Life Expectancy: 3 years (for typical use)
Battery Supervision: Automatic reporting of battery status with
each alarm and with periodic supervision message.
Nominal Battery Capacity: 750 mAh
Standby Current Drain: 0.015 mA
Transmit Current Drain: 20 mA (including LED)
Battery Life Expectancy: 3 years (for typical use)
Battery Supervision: Automatic reporting of battery status with
each alarm and with periodic supervision message.
FUNCTIONAL
True Motion Event Verification: 2 position selector - 1 (OFF) or
2 (ON) motion events.
Alarm Period: 3 seconds.
True Motion Event Verification: 2 position selector - 1 (OFF) or
2 (ON) motion events.
Alarm Period: 3 seconds.
Visual Indications:
LED lights for about 3 seconds upon transmission of alarm &
tamper messages and upon each motion detection in the walk
test mode.
LED flashes during the power-up stabilization period, or after
restoring (pressing) the tamper switch.
LED does not light upon transmission of supervision
messages.
tamper messages and upon each motion detection in the walk
test mode.
LED flashes during the power-up stabilization period, or after
restoring (pressing) the tamper switch.
LED does not light upon transmission of supervision
messages.
Rearm Timer: Rearms the detector 2 minutes after the last alarm.
Timer disabled in the walk test mode.
Timer disabled in the walk test mode.
WIRELESS
Frequency (MHz): 315, 433.92, 868.95, 869.2625 or other
frequencies according to local requirements.
Transmission Sequence: 3 data bursts at variable intervals
within 3 seconds.
Encoding: 24-bit ID, over 16 million possible combinations.
Total Message Length: 36 bits.
Tamper Alert: Reported when a tamper event occurs and in any
subsequent message, until the tamper switch is restored.
Supervision Message: Once per 15 minutes, 60 minutes or
according to local standards.
Frequency (MHz): 315, 433.92, 868.95, 869.2625 or other
frequencies according to local requirements.
Transmission Sequence: 3 data bursts at variable intervals
within 3 seconds.
Encoding: 24-bit ID, over 16 million possible combinations.
Total Message Length: 36 bits.
Tamper Alert: Reported when a tamper event occurs and in any
subsequent message, until the tamper switch is restored.
Supervision Message: Once per 15 minutes, 60 minutes or
according to local standards.
MOUNTING
Height:
Height:
With bracket : Up to 3.6 m (12 ft)
Without bracket: 2 - 2.6 m (6.5 - 8.5 ft)
Without bracket: 2 - 2.6 m (6.5 - 8.5 ft)
Installation Options:
With bracket: Surface or ceiling
Without bracket: Surface or corner
Without bracket: Surface or corner
Bracket Adjustment: 20
°
downward, 20
°
left and right.
ENVIRONMENTAL
RFI Protection: >30 V/m up to 1000 MHz.
Operating Temperatures: -10
RFI Protection: >30 V/m up to 1000 MHz.
Operating Temperatures: -10
°
C to 50
°
C (14
°
F to 122
°
F).
Storage Temperatures: -20
°
C to 60
°
C (-4
°
F to 140
°
F).
Compliance with Standards: Designed to meet FCC Part 15
and Directive 1999/5/EC of the European Parliament.
PHYSICAL
Dimensions (H x W x D): 117 x 65 x 47 mm.
and Directive 1999/5/EC of the European Parliament.
PHYSICAL
Dimensions (H x W x D): 117 x 65 x 47 mm.
(4-5/8 x 2-9/16 x 1-7/8 in.).
Weight:
Weight:
92
g
(3.25 oz) without bracket, 107
g (3.75
oz) with
bracket.
Color: White
PATENTS: U.S. Patent No. 5,693,943
Color: White
PATENTS: U.S. Patent No. 5,693,943