Climax Technology Co Ltd 862 ユーザーズマニュアル
1
PIR Motion Sensor Camera
VST-862P-F1
Introduction
VST-862P-F1
Introduction
VST-862P-F1 is a passive infrared (PIR) motion sensor camera. It is capable of sending wireless signals and captured
images (picture quality of up to 640 x 480 pixels) to the Control Panel upon movement detection.
The PIR Camera is designed to give a typical detection range of 12 meters when mounted at 2 meters above ground. It
has a pet-immune range of 7 meters and will not trigger false alarm from your household pets within this distance.
The PIR Camera consists of a two-part design made up of a cover and a base. The cover contains all the electronics and
optics and the base provides a means of fixing. The base has knockouts to allow mounting on either a flat surface or in a
corner situation with a triangular bracket for corner mounting.
images (picture quality of up to 640 x 480 pixels) to the Control Panel upon movement detection.
The PIR Camera is designed to give a typical detection range of 12 meters when mounted at 2 meters above ground. It
has a pet-immune range of 7 meters and will not trigger false alarm from your household pets within this distance.
The PIR Camera consists of a two-part design made up of a cover and a base. The cover contains all the electronics and
optics and the base provides a means of fixing. The base has knockouts to allow mounting on either a flat surface or in a
corner situation with a triangular bracket for corner mounting.
Parts Identification
1. Flash LED
The Flash LED delivers sufficient light for image capture under low lighting
condition.
condition.
2. Blue LED/Function Button
Blue LED:
(Please refer to LED Indicator description below for details)
Function Button Usage:
(Please refer to LED Indicator description below for details)
Function Button Usage:
- Press and hold the button for 3 seconds to send a learn code, release when Blue
LED light on.
- Press the button once to enter test mode for 3 minutes.
3. IR Sensor
4. PIR Camera Lens
5. Battery Compartment Cover
6. Tamper Switch
7. Battery Compartment
8. Sensitivity Adjustment Jumper Switch (JP3)
4. PIR Camera Lens
5. Battery Compartment Cover
6. Tamper Switch
7. Battery Compartment
8. Sensitivity Adjustment Jumper Switch (JP3)
- Jumper On: the PIR’s sensitivity level is set to High.
- Jumper Off: the PIR’s sensitivity level is set to Normal. (Factory Default)
- Jumper Off: the PIR’s sensitivity level is set to Normal. (Factory Default)
9. Sleep Timer Jumper Switch (JP2)
- Jumper On: After movement detection, the PIR Camera does not enter sleep mode and
will transmit detection signal again immediately if triggered (Factory Default).
- Jumper Off: PIR Camera has a “sleep time” of approximately 1 minute after motion
detection to conserve power.
Features
LED Indicator
In Normal operation mode, the Blue LED will not light except in the following situations:
When the PIR Camera is in low battery condition, every time it transmits a detected movement, the Blue LED will
flash for 2 seconds.
flash for 2 seconds.
When the cover is opened and the tamper switch is violated, the Blue LED will flash for 2 seconds, to indicate it is
transmitting “Tamper” signal.
transmitting “Tamper” signal.
When the Tamper condition persists, every time it transmits a detected movement, the Blue LED will flash for 2
seconds.
seconds.
When PIR Camera enters Test Mode, the Blue LED will flash for 1 second. During Test mode, the Blue LED will
Jumper On
The jumper link is inserted
connecting the two pins.
connecting the two pins.
Jumper Off
if the jumper link is removed
or “parked” on one pin.
or “parked” on one pin.
Jumper On
The jumper link is inserted
connecting the two pins.
connecting the two pins.
Jumper Off
if the jumper link is removed
or “parked” on one pin.
or “parked” on one pin.