Climax Technology Co Ltd IRPF1 ユーザーズマニュアル

The PIR detects infrared signature to pick up movements within an assigned area and signals the Control Panel to activate the alarm if an 
intruder crosses its’ path of detection. 
The PIR consists of a two-part design made up of a cover and a base. The cover contains all the electronics and optics and the base provides a 
means of fixing. The base has knockouts to allow mounting on either a flat surface or in a corner situation 
The PIR has a tamper switch which will be activated when the cover is opened. It can also alert you to signal communication problems and low 
battery situations. 
The PIR is designed to give a typical detection range of 12 meters when mounted at 2 meters above ground. 
The Pet-Immune models of IR-29 series PIR sensor further support pet immunity feature and will not detect pets of up to 27 kg within 7 meter 
range to minimize false alarm situation.   
The IR-29 Series PIR Sensor includes the following models: 
IR-29 / IR-29 F1 – PIR sensor with alkaline batteries 
IRP-29 / IRP-29 F1 – Pet Immune PIR sensor with alkaline batteries 
IR-29 Lithium / IR-29-F1 Lithium – PIR sensor with lithium battery. 
IRP-29 Lithium / IRP-29-F1 Lithium – Pet Immune PIR sensor with lithium battery 
 

  Identifying the Parts 

The test button is used for testing the radio performance and for learning purpose. 
The LED indicator is used to indicate the status of system.   

 
 
 

-  When set as ON, Supervision is disabled. (Factory default for 433AM frequency models) 

-  When set as OFF, Supervision is enabled. (Factory default for 868WF frequency models) 

433 FM and 868FM frequency models does not support JP2 Jumper Switch, Supervision is enabled 
and cannot be disabled. 

-  When set as OFF, the PIR’s detection sensitivity is in normal level. (Factory default for non Pet-Immune 

-  When set as ON, the PIRs detection sensitivity is high. (Factory default for Pet-Immune models) 

The Tamper switch protects the PIR from unauthorized cover opening. 

  Sleep Timer 

The PIR has a “sleep time” of approximately 1 minute to conserve power. After transmitting a detected 
movement, the PIR will not retransmit for 1 minute; any further movement detected during this sleep period will 
extend the sleep time by another minute. In this way continuous movement in front of a PIR will not unduly exhaust the battery. 

  Supervision Function 

If enabled (see table above), when the PIR is in Normal operation mode it will conduct a Self-test Periodically by transmitting a supervisory 
signal once every 30 to 50 minutes 
If the Control Panel fails to receive the Supervisory signals transmitted from a certain PIR for a preset time, an “Out-Of-Order” fault 
message will be generated.   

  Sensitivity Increaser Function 

You can use the sensitivity increaser function to increase the PIR’s detection sensitivity. To increase detection sensitivity, connect the 
Jumper Switch (JP3), or the ON position (Factory default for Pet-Immune models). To maintain normal detection sensitivity, disconnect the 
Jumper Switch (JP3), or the OFF position (Factory default for non-Pet-Immune models). 

  Test Mode 

The PIR can be put into Test mode by pressing the Test Button on the front cover. In Test mode, it will disable the sleep timer and will enable 
the LED indicator to flash every time a movement is detected. Every time the Test Button is pressed, the PIR will transmit a test signal to the 
Control Panel for radio range test and enter the test mode for 3 mins. Test Mode will time out after 3 minutes.. 

  LED Indicator 

In Normal operation mode, the LED Indicator light up in the following situations (For F1 models, the LED flashes instead): 
  When movement is detected under low battery condition 
  When the cover is opened and the tamper switch is triggered. 
  When movement is detected if the Tamper condition persists. 
  When movement is detected under Test mode 
  When the Test Button is pressed under tamper condition or if PIR is under low battery. 

  Battery 

IR-29 Series PIR Motions sensor uses with alkaline or lithium batteries as power source: 
- 

The alkaline-powered models use two alkaline AA 1.5 V batteries as its power source. 

- 

The lithium-powered models use one 3V 2/3A (EL123AP) Lithium battery as its power source. 

The PIR features low battery detection function. If low battery voltage is detected, a low battery signal will be sent to the Control Panel 
along with regular signal transmissions for the Control Panel to display the status accordingly.   
For each installation, the battery is installed in by the factory before shipment with an Insulator inserted.

   

The jumper link is inserted 
connecting the two pins

 

if the jumper link is removed or “parked” 
on one pin.