Climax Technology Co Ltd RSB ユーザーズマニュアル
1
HUE
ZigBee Color LED Light Bulb
Introduction
ZigBee Color LED Light Bulb
Introduction
The Hue is a ZigBee Color LED Light Bulb. It features both multicolor adjustment and light
level control. When joined into a ZigBee network, the user will be able to control Hue
remotely from the ZigBee network coordinator.
The Hue utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless
communication protocol that is reliable and has low power consumption and high
transmission efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount
of devices to be included in a network and coordinated for data exchange and signal
transmission
The Hue serves as an end device in the ZigBee network. It can be included in the ZigBee
network to receive command for color and light level control, but cannot permit any other
ZigBee device to join the network through the Hue.
level control. When joined into a ZigBee network, the user will be able to control Hue
remotely from the ZigBee network coordinator.
The Hue utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless
communication protocol that is reliable and has low power consumption and high
transmission efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount
of devices to be included in a network and coordinated for data exchange and signal
transmission
The Hue serves as an end device in the ZigBee network. It can be included in the ZigBee
network to receive command for color and light level control, but cannot permit any other
ZigBee device to join the network through the Hue.
ZigBee Network Setup
Joining the ZigBee Network
Please follow the steps below to join the device into the ZigBee network.
The PIR Camera can only join ZigBee network within 3 minutes after power on.
1. Install the Hue on lamp holder. Do not supply power yet.
2. Enable the permit-join feature on the router or coordinator of your ZigBee network.
3. Switch ON Hue for 3~5 seconds. (No more than 5 seconds), then switch OFF.
4. Repeat Step 3 for 3 times for a total of 4 ON/OFF cycles
5. Switch ON Hue for the 5
The PIR Camera can only join ZigBee network within 3 minutes after power on.
1. Install the Hue on lamp holder. Do not supply power yet.
2. Enable the permit-join feature on the router or coordinator of your ZigBee network.
3. Switch ON Hue for 3~5 seconds. (No more than 5 seconds), then switch OFF.
4. Repeat Step 3 for 3 times for a total of 4 ON/OFF cycles
5. Switch ON Hue for the 5
th
time, the device will reset and start searching for new ZigBee network.
6. After joining the ZigBee network, the PIR Camera will be registered in the security system in the network
automatically. Please check the ZigBee network coordinator, system control panel, or CIE (Control and Indicating
Equipment) to confirm if joining and registration is successful.
Equipment) to confirm if joining and registration is successful.
Removing Device from ZigBee Network (Factory Reset)
To remove the Hue from current ZigBee network, the device must be put to Factory Reset to complete device
removal. Factory Reset function will clear the Hue of its stored setting and information and prompt the Hue to search
for new ZigBee network.
Before removing device, make sure the Hue is within current ZigBee network signal range
1. Delete the Hue from current control panel / CIE.
2. Power off the Hue.
3. Switch ON Hue for 3~5 seconds. (No more than 5 seconds), then switch OFF.
4. Repeat Step 3 for 3 times for a total of 4 ON/OFF cycles
5. Switch ON Hue for the 5
removal. Factory Reset function will clear the Hue of its stored setting and information and prompt the Hue to search
for new ZigBee network.
Before removing device, make sure the Hue is within current ZigBee network signal range
1. Delete the Hue from current control panel / CIE.
2. Power off the Hue.
3. Switch ON Hue for 3~5 seconds. (No more than 5 seconds), then switch OFF.
4. Repeat Step 3 for 3 times for a total of 4 ON/OFF cycles
5. Switch ON Hue for the 5
th
time, the device will reset and start searching for new ZigBee network.
6. Upon reset, the PIR Camera will clear current ZigBee network setting and transmit signal to ZigBee coordinator
to remove itself from current ZigBee network. It will then actively search for available ZigBee network again and
join the network automatically.
join the network automatically.
Features
Color and Saturation Adjustment
The Hue’s color and saturation may be adjusted from the ZigBee Coordinators remotely by sending commands.
Light Level Adjustment
The Hue has dimmable lighting, the light percentage maybe adjusted from the ZigBee Coordinators remotely by