Climax Technology Co Ltd TS9 ユーザーズマニュアル
1
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
S
S
e
e
n
n
s
s
o
o
r
r
(
(
T
T
S
S
-
-
9
9
E
E
L
L
)
)
TS-9EL is a temperature wireless sensor device. It transmits temperature condition to the Control
Panel every 30 minutes.
Panel every 30 minutes.
I
I
d
d
e
e
n
n
t
t
i
i
f
f
y
y
i
i
n
n
g
g
t
t
h
h
e
e
p
p
a
a
r
r
t
t
s
s
Remove the cover by loosening the bottom fixing screw using a Philips screwdriver, the inside
of the Temperature Sensor will be revealed as shown.
of the Temperature Sensor will be revealed as shown.
1. Temperature Switch
Press this switch to send status information to the
Control Panel.
Control Panel.
2. Internal LED
Flashes 3 times –when pressing the Learn/Status
Button.
Flashes every 4 seconds – Battery exhaustion
Button.
Flashes every 4 seconds – Battery exhaustion
3. Learn/Status Button
Pressing the switch will send out a learn code. The
status information is also transmitted to inform the
control panel the status of the Temperature Sensor.
status information is also transmitted to inform the
control panel the status of the Temperature Sensor.
4. Battery Compartment
5. Internal Temperature Probe
Battery
The Temperature Sensor uses one CR123 - 3V Lithium battery. Please always replace
battery with the correct size and voltage.
When the Temperature Sensor is low battery, a low battery signal will be sent to the Control
Panel along with regular signal transmissions for the Control Panel to display the status
accordingly.
When the battery is depleted, the LED flashes every 4 seconds and the Temperature Sensor
will stop all functions.
battery with the correct size and voltage.
When the Temperature Sensor is low battery, a low battery signal will be sent to the Control
Panel along with regular signal transmissions for the Control Panel to display the status
accordingly.
When the battery is depleted, the LED flashes every 4 seconds and the Temperature Sensor
will stop all functions.
Battery Change
I. Remove the Cover by loosening the bottom fixing screw using a Philips screwdriver.
II. Remove the Old Battery.
III. Press the Temperature Switch or the Learn/Status Button a few times.
IV. Fit a new battery into the battery compartment. Please orient the battery according
II. Remove the Old Battery.
III. Press the Temperature Switch or the Learn/Status Button a few times.
IV. Fit a new battery into the battery compartment. Please orient the battery according
to the correct polarity.
V. Replace the Cover and lightly tighten the bottom fixing screw using a Philips
screwdriver.
Getting Started
Step 1 Remove the base and cover assembly by loosening the bottom fixing screw using a
Philips screwdriver.
Step 2 Insert the battery into the battery holder taking care to connect the polarity correctly.
Step 3 Put the Control Panel into learning mode. Please refer to your Control Panel user
Step 3 Put the Control Panel into learning mode. Please refer to your Control Panel user
manual.
Step 4 Press Learn/Status Button to send learn code to Control Panel.
Step 5 Refer to the user manual of the Control Panel to complete the learn-in process.
Step 6 To check for range, put the Control Panel into range test mode (or Walk Test mode).
Step 5 Refer to the user manual of the Control Panel to complete the learn-in process.
Step 6 To check for range, put the Control Panel into range test mode (or Walk Test mode).
Please refer to the control panel user manual. Conduct the range test of the Control
Panel by pressing the Learn/Status Button of the Temperature Sensor.
Panel by pressing the Learn/Status Button of the Temperature Sensor.