HeathCo LLC 60WRC14TX ユーザーズマニュアル
DRAFT COPY
FEATURES
• Products are UL/cUL and/or FCC/IC tested and approved.
• Operational range of up to 100 feet.
• Operational range of up to 100 feet.
This manual applies to the following products:
• Wall Switch Transmitter
• Wall Switch Receiver
• Wall Switch Transmitter
• Wall Switch Receiver
Remote Controlled Products
This manual includes operating instructions for a variety of remote controlled products. All products work on the same principle and use the same
channel setting information. Please read all instructional information and note any specific information pertaining to your particular product.
channel setting information. Please read all instructional information and note any specific information pertaining to your particular product.
WARNINGS:
• FOR USE ONLY with 120 volt incandescent or halogen bulbs.
• DO NOT USE with fluorescent bulbs, appliances, power supplies, low voltage lighting, or any other electrical devices.
• FOR USE ONLY with 120 volt incandescent or halogen bulbs.
• DO NOT USE with fluorescent bulbs, appliances, power supplies, low voltage lighting, or any other electrical devices.
© 2002 DESA International
598-1135-00
ENGLISH
WALL SWITCH TRANSMITTER
Installation
1. Select mounting location for wall switch transmitter.
Note:
Transmitter should be located within 100 feet
(30 m) of receiver.
2. Before mounting, place transmitter in selected lo-
cation and verify operation (see
Operation
).
Note:
If transmitter does not operate correctly, see
Troubleshooting Guide
).
3.
Mount transmitter to wall using two #8 x 1 3/4" wood screws
(provided). Transmitter should be mounted approximately 4
feet from the floor and in the vertical position. Use drywall
anchors (provided) if not mounting to wall stud.
(provided). Transmitter should be mounted approximately 4
feet from the floor and in the vertical position. Use drywall
anchors (provided) if not mounting to wall stud.
Operation
1.
Verify power disconnect switch on wall switch receiver is in
ON position. Wall switch transmitter will not operate lights if
power disconnect switch is in OFF position.
ON position. Wall switch transmitter will not operate lights if
power disconnect switch is in OFF position.
2.
Push the ON (top) button and release. The light should turn
on full bright.
on full bright.
3.
Push the OFF (bottom) button and release. The light should
turn off.
turn off.
4.
Push the DIM button and release. The light should turn on at
50% brightness (or last setting).
50% brightness (or last setting).
5.
Continue to press the DIM button until the desired dim level
is reached.
is reached.
Note:
DIM setting remembers last setting used.
To recall last DIM setting, push and release the DIM button.
Note:
The DIM setting defaults to 50% in the event of a power
failure.
Important:
Wait 1 to 2 seconds after you press a transmitter
button before you press it again to allow the transmission to be
completed.
completed.
Note:
If light does not turn on or intermittently turns on and off when
transmitter buttons are pushed, see
Troubleshooting Guide
.
DIM
Wall Switch Transmitter
Wall Switch
ON/OFF
Button
DIM
Button
Access Door
DIM
Battery Replacement
The wall switch transmitter requires a type CR2032, 3-volt
lithium battery to operate. The transmitter is shipped with the
battery installed. With typical use, the battery will last approxi-
mately one year. Remove battery when transmitter will not be
used for an extended period of time.
1.
lithium battery to operate. The transmitter is shipped with the
battery installed. With typical use, the battery will last approxi-
mately one year. Remove battery when transmitter will not be
used for an extended period of time.
1.
Place thumb on access
door and slide down to
open.
door and slide down to
open.
2.
Carefully bend locking
tab outward. Battery will
pop up.
tab outward. Battery will
pop up.
3.
Remove battery from
socket.
socket.
4.
Install replacement bat-
tery in socket plus (+)
side up (see illustra-
tion). Press down on
battery until locking tab
snaps into place.
tery in socket plus (+)
side up (see illustra-
tion). Press down on
battery until locking tab
snaps into place.
5.
Reinstall access door
by sliding it upward until it locks in place.
by sliding it upward until it locks in place.
1 2
3 4
ON
DIM
2032
3
V
Li
thiu
m Ba
tte
ry
CR2032
Lithium
Battery
Battery
Locking
Tab
Access
Door
Removing Access Door and
Battery