HeathCo LLC WLTX207 ユーザーズマニュアル

THANK YOU 

Illustrations may vary from actual unit.

1. 

Please read and understand this entire manual before attempting to assemble, install, 
or operate this push button.

WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near 
batteries. If battery is swallowed, immediately notify a doctor.

NOTE: The range of the wireless doorbell can vary with location, temperature, and battery 
condition.

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. 
Operation is subject to the following two conditions: (1) this device may not cause 
harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.

The user is cautioned that changes or modifications not expressly approved by the party 
responsible for regulatory compliance could void the user’s authority to operate the 
equipment.

 

Use a dry cloth to clean the push button.

 

Do not use cleaners or polishes.

 

Do not use any fluids on the push button.

Phillips screwdriver

Small flathead screwdriver

A

Push button

1

B

Jumper

1

C

Screw

2

D

Double-sided tape

1

Battery - pre-installed (not shown)

1

1 

… Remove the back of the push 

button by pushing in the tab on the 
bottom with a small screwdriver 
(not included).

… Remove the orange battery tab 

from the push button.

2 

… Press and hold the “SYNC” button 

on the doorbell until the doorbell 
sounds a “Beep-Beep”.

… Press the push button within 30 

seconds. The doorbell will sound a 
“Beep-Beep” tone to indicate the 
push button is synced.

… Press the push button to confirm 

sync. If the doorbell sounds, sync 
is complete.

SYNC – PRESS
AND RELEASE

.

RESET – HOLD
   10 SECONDS.

TUNE – HOLD
   1 SECOND.

30

3 

… Temporarily position the push 

button where you want it mounted.

… Press the push button to verify 

the doorbell and push button work 
properly. If the doorbell does not 
sound, see Troubleshooting.

NOTE: Do not permanently mount the 
push button until the push button and 
doorbell are working properly.

SYNC – PRESS
AND RELEASE

.

RESET – HOLD
   10 SECONDS.

CH

IM

E

 V

O

LU

ME

TUNE – HOLD
   1 SECOND.

FRONT TRANS REAR

This product is guaranteed to be free of factory defective parts and workmanship for a 
period of 3 years from date of purchase. Purchase receipt is required for all warranty 
claims.

This warranty does not include expendable items (such as light bulbs, batteries, etc.), repair 
service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized 
service or modification of the product or of any furnished component will void this warranty 
in its entirety. This warranty does not include reimbursement for inconvenience, installation, 
setup time, loss of use, unauthorized service, or return shipping charges. This warranty 
is not extended to other equipment and components that a customer uses in conjunction 
with this product.

Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com.

Questions, problems, missing parts? 

Before returning to the store, call Hampton Bay Customer Service 

8 a.m. - 5 p.m., CST, Monday - Friday

1-844-760-3644

4 

Use either screws or double-sided tape 
to mount the push button.

… To mount with screws, remove the 

back of the push button by pushing 
in the tab on the bottom with a 
small screwdriver. Place the push 
button back on the door jamb and 
mark the two screw holes. Attach 
with screws and snap on the front 
of the push button.

… When attaching the push button 

with double-sided tape, remove 
paper from both sides of the 
double-sided tape and apply to a 
clean surface.

5 

Wireless doorbells have different selectable tunes. The wireless push button can be set 
to play one of those tunes by adding or removing the jumper inside the push button. 
See the table below for tune selection.

Rear door

Front door

NOTE: Refer to the doorbell manual for available tunes.

 

Push Button 

Push Button 

 

Jumper OFF 

Jumper ON

Type 2032 3V battery

The doorbell does not sound.

Make sure batteries are installed according 

to the diagram inside the push button and 

doorbell (if applicable).

Check the charge of the push button and 

doorbell batteries (if applicable) and replace 

if necessary.

Make sure the plug-in doorbell has power 

(if applicable).

Push button and doorbell are not synced. 

Follow step 2 under installation to sync.

The batteries seem okay, but the 

doorbell does not work after installation.

Metal reduces transmission range. Use 1/4 

in. to 1/2 in. (6 to 13 mm) wood shims to 

move the doorbell or push button away from 

the metal surface.

Concrete may reduce range. Move the 

doorbell away from the concrete surface.

Locate the doorbell closer to the push 

button.

208198-01A

A

B

C

D