Ranger Electronic Communications Inc 5054DX ユーザーズマニュアル
- 12 -
Programming (Continued)
Receive Scanning
The receive scanning feature allows you to locate active frequencies in the
entire band segment. To begin scanning , slowly turn the Squelch control
clockwise until the receiver noise disappears. Next, press the scan button.
The unit should start scanning from the lower to the higher frequencies.
Pressing the Scan button again will change the direction of scanning. When
the Scan button is pressed ,"SCAN+" or "SCAN-" will be displayed on the
LCD display . The scan will stop on any active frequency for the duration of
the transmission. When the transmission stops, the RCI-5054DX will wait
approximately 2 seconds before it resumes scanning. If you want to
deactivate Scan mode while it's scanning, press the MAN (manual) button or
turn the Squelch control counterclockwise until you hear the receiver noise.
The MAN button will disable the Scan function. (See FREQUENCY
SCANNING, pg. 15 for more information.)
entire band segment. To begin scanning , slowly turn the Squelch control
clockwise until the receiver noise disappears. Next, press the scan button.
The unit should start scanning from the lower to the higher frequencies.
Pressing the Scan button again will change the direction of scanning. When
the Scan button is pressed ,"SCAN+" or "SCAN-" will be displayed on the
LCD display . The scan will stop on any active frequency for the duration of
the transmission. When the transmission stops, the RCI-5054DX will wait
approximately 2 seconds before it resumes scanning. If you want to
deactivate Scan mode while it's scanning, press the MAN (manual) button or
turn the Squelch control counterclockwise until you hear the receiver noise.
The MAN button will disable the Scan function. (See FREQUENCY
SCANNING, pg. 15 for more information.)
Split Function
This function enables you to split the transmit and receive frequencies for
FM repeater operation. To split frequencies, press the MAN button and the
Split button to select + split frequency. If you want - split frequency, press
the Split button again. If + split is selected, the transmit frequency will be
higher than the receiver frequency. If - split is selected, it will be lower than
the receive frequency. (See OFFSET FREQUENCY OPERATION, pg. 18 for
more information.)
FM repeater operation. To split frequencies, press the MAN button and the
Split button to select + split frequency. If you want - split frequency, press
the Split button again. If + split is selected, the transmit frequency will be
higher than the receiver frequency. If - split is selected, it will be lower than
the receive frequency. (See OFFSET FREQUENCY OPERATION, pg. 18 for
more information.)
Memory
Function
The RCI-5054DX can store up to 10 channels (from 0 to 9). To program a
frequency into memory , follow the procedure described below :
1. Press the MAN button.
2. Press the PRG button.
frequency into memory , follow the procedure described below :
1. Press the MAN button.
2. Press the PRG button.
3. Press the MEM button. ("MEMORY" and "0" should appear on the left-
hand side of the LCD display. Pressing the MEM button will advance the
channel number from "0" to "9".)
channel number from "0" to "9".)
- 13 -
Programming (Continued)
4. Select the desired frequency you wish to store in memory.
5. Press the ENT button.
6. Repeat the procedure to program other memory channels.
5. Press the ENT button.
6. Repeat the procedure to program other memory channels.
Memory Channel Scanning
You can scan and select any of the 10 programmed frequencies by following
the procedure described below:
the procedure described below:
1. Press MAN button.
2. Press the MEM button.
3. Slowly turn the Squelch knob clockwise until the receiver noise
2. Press the MEM button.
3. Slowly turn the Squelch knob clockwise until the receiver noise
disappears.
4.Press the Scan button. The unit will scan from lower to higher frequencies.
Pressed again, the unit will scan from higher to lower frequencies.
5. To stop scanning a certain channel, press the MAN button, or turn the
Squelch knob counterclockwise until you hear the receiver noise.
Metering
The meter built into your RCI-5054DX on the left-hand side of the LCD
display provides the following information:
display provides the following information:
1. S/RF METER : In transmit mode it provides a visual indication of transmit
RF output power and received signal strength on the receive mode.
2. SWR METER : This meter enables you to check SWR. To use this
function, set the unit to AM mode and push the SWR button on the front
panel while holding down the PTT switch on the microphone. The bars on
the meter will indicate antenna matching. If there is no bar, your antenna
system is perfectly matched. If several bars appear, the antenna needs
adjustment. The fewer the bars, the better the match.
panel while holding down the PTT switch on the microphone. The bars on
the meter will indicate antenna matching. If there is no bar, your antenna
system is perfectly matched. If several bars appear, the antenna needs
adjustment. The fewer the bars, the better the match.