ademco 8DLTSSCKP ユーザーズマニュアル
TSSKP112011U
Wireless Bidirectional Alpha Keypad
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The TSSKP112011U (hereinafter the Keypad) is a wireless
bidirectional alpha keypad that is used in conjunction with the
TSSBU111011U (Base). The Keypad should be used as an auxiliary
keypad in addition to the Base.
bidirectional alpha keypad that is used in conjunction with the
TSSBU111011U (Base). The Keypad should be used as an auxiliary
keypad in addition to the Base.
Up to a total of eight (8) Keypads can be used on the system.
ENROLLING OR DELETING ENROLLED KEYPADS
The Keypads must be enrolled using the TSSC Installer App
(https://portal.adtpulse.com/activation). Previously enrolled Keypads
may be deleted if desired using the TSSC Installer App.
(https://portal.adtpulse.com/activation). Previously enrolled Keypads
may be deleted if desired using the TSSC Installer App.
PROGRAMMING SRID AND KEYPAD ID
Additional Keypad(s) or replacement Keypads are added to the TSSC
system as follows:
system as follows:
1. Remove back cover, power, and battery from Keypad.
2. Apply power and within 30 seconds hold down the 1 and 3 keys
2. Apply power and within 30 seconds hold down the 1 and 3 keys
simultaneously until PROGRAM MODE is displayed.
3. If the Keypad has been previously installed on a different system,
hit the # key until DEFAULT KEYPAD is displayed. Press 3 =
Yes, then press the # key to accept. Repeat step 2.
Yes, then press the # key to accept. Repeat step 2.
4. Enter SRID xxxxx into the SRID field and press #. (The SRID is
found on the back of the Base or within the Installer App).
5. Enter a unique Keypad ID (01-08) and press #.
6. Press the * key to save and exit Keypad Program Mode.
6. Press the * key to save and exit Keypad Program Mode.
KEYPAD MOUNTING
The Keypad is designed to be placed on a desk/table top with the
stand attached. An optional mounting plate (PN TSSKP112041U)
can be used to mount the keypad to the wall.
stand attached. An optional mounting plate (PN TSSKP112041U)
can be used to mount the keypad to the wall.
POWER CONNECTIONS
The Keypad is powered from an external 110VAC input/9VDC output
power pack (supplied). A 7.2VDC battery back provides 24-hour
backup power.
power pack (supplied). A 7.2VDC battery back provides 24-hour
backup power.
Connect the Power Supply Cable into its connector as shown below
and route it from the bottom of the Keypad.
and route it from the bottom of the Keypad.
IMPORTANT: Do not apply power to the Keypad at this time.
INSTALLING KEYPAD TO DESK-TOP STAND
1.
Place the Keypad face down on a level surface.
2.
Connect the battery connector to the receptacle on the PC board.
3.
Secure the Battery Pack into the case.
4.
Secure the Battery Pack with the Battery Retainer using the
Retaining Screw.
5.
Install tabs on Desk Stand into appropriate slots as shown and
secure with two screws.
6.
Plug in the power pack to the receptacle.
BATTERY REPLACEMENT – DESK TOP
CONFIGURATION
CONFIGURATION
1. Disconnect power to the Keypad.
2. Remove two screws securing the Desk Stand to the Keypad.
3. Loosen screw that secures the battery retainer and slide battery
2. Remove two screws securing the Desk Stand to the Keypad.
3. Loosen screw that secures the battery retainer and slide battery
retainer upward.
4. Lift battery from battery compartment and disconnect the
battery from the Keypad.
5. Connect the new battery to the keypad and place the battery in
the battery compartment.
6. Slide the battery retainer down so that the battery is secured and
tighten the screw.
7. Install the tabs on Desk Stand into appropriate slots and secure
with two screws.
8. Connect power to the Keypad.
INSTALLING WALL MOUNTED KEYPAD (OPTIONAL)
1. Secure the Wall Mounting Plate (not supplied) to the wall.
2. Connect the Power Supply Cable into its connector as shown and
2. Connect the Power Supply Cable into its connector as shown and
route it from the bottom of the Keypad.
3. Align the Keypad with the Wall Mounting Plate and slide the
Keypad downward until it locks in place.
4. Secure the Keypad onto the wall mounting plate with the
retaining screw.
5. Connect power to the Keypad.
BATTERY REPLACEMENT – WALL MOUNTED KEYPAD
1. Disconnect power to the Keypad.
2. Remove the retaining screw at the bottom of the Keypad.
3. Press upward with your thumbs on the bottom edge of the
2. Remove the retaining screw at the bottom of the Keypad.
3. Press upward with your thumbs on the bottom edge of the
Keypad housing and slide the Keypad up with respect to the wall
mounting plate, removing the Keypad from the wall mounting
plate.
mounting plate, removing the Keypad from the wall mounting
plate.
4. Connect the power harness to the printed circuit board.
5. Replace the Keypad onto the wall mounting plate and secure
5. Replace the Keypad onto the wall mounting plate and secure
with the retaining screw.
TSSKP112011U SPECIFICATIONS:
Physical:
6.69” W x 5.36” H x 0.875” D (169.78mm x
136.03mm x 22.03mm)
136.03mm x 22.03mm)
Frequency of
Operation:
Operation:
345 MHz
Battery Pack:
P/N TSSKP112061U: 7.2V, 6xAAA, 6x600mAH,
NiMH
NiMH
Transformer:
P/N 300-05763: 110 VAC input/9 VDC output 2.5A,
2-prong
2-prong
LCD Display:
2x16, COG, 6V, B/W
Sounder:
Piezoelectric
NOTE: After installing the battery and reattaching the Keypad to
the mounting plate, enter 4-digit User code + OFF sequence twice to
clear any trouble condition.
the mounting plate, enter 4-digit User code + OFF sequence twice to
clear any trouble condition.
PLEASE GO TO BOTTOM OF
THE NEXT PAGE FOR FCC / IC
AGENCY STATEMENTS.
THE NEXT PAGE FOR FCC / IC
AGENCY STATEMENTS.