Westell Inc. A9080YYXX-07 ユーザーズマニュアル
UltraLine II – Draft 1
030-300459 Rev. A
7/12/05
030-300459 Rev. A
15
July 2005
User Guide
UltraLine II (Model 800015)
10. Connect the attached ADSL device to the ADSL-equipped jack on the wall. IMPORTANT: If the attached
ADSL device is a Modem, do not use a DSL filter on this connection. You must use the phone cord that was
provided with your kit.
provided with your kit.
11. Connect an Ethernet cable from any one of the four Ethernet jacks marked ETHERNET on the rear panel of the
Modem to the Ethernet port on your computer. Repeat this step to connect up to three additional PCs to the
UltraLine II.
UltraLine II.
NOTE: You may connect to any of the four Ethernet jacks on the rear panel of the UltraLine II because they
serve as an Ethernet switch.
serve as an Ethernet switch.
4.
Connect the power supply cord to the power connector marked 12 VDC on the rear panel of the UltraLine II.
Plug the other end of the power supply into a wall socket, and then turn on the power switch (if it is not already
turned on).
Plug the other end of the power supply into a wall socket, and then turn on the power switch (if it is not already
turned on).
5.
Check to see if the UltraLine’s POWER LED is solid green. This indicates that the UltraLine II is powered on.
6.
Check to see if the UltraLine’s Ethernet LED is solid green. Solid green indicates that the Ethernet connection is
functioning properly.
functioning properly.
7.
Check to see if the UltraLine’s WAN LED is solid green. Solid green indicates that the WAN connection is
functioning properly. (The UltraLine’s LAN and WAN traffic will be uplinked to the attached ADSL device.)
functioning properly. (The UltraLine’s LAN and WAN traffic will be uplinked to the attached ADSL device.)
NOTE: You may need to set the UltraLine II to uplink mode. Refer to section 15.9 “WAN Configuration,” for
instructions.
instructions.
8.
Check to see if the UltraLine’ WIRELESS LED is solid green. This means that the Wireless interface is
functioning properly.
functioning properly.
9.
Check to see if the UltraLine’s INTERNET LED is solid green. Solid green indicates that an Internet link as
been established.
been established.
Congratulations! You have completed the Wireless installation for your Modem. You must now proceed to section 8,
“Accessing the UltraLine II,” for instructions on configuring the Modem for Internet connection.
6.3.3 Connecting via Coax
1. Connect the Coax cable from the wall to the jack labeled Coax on the rear panel of the UltraLine II.
2. Connect an Ethernet cable from any one of the four Ethernet jacks marked ETHERNET on the rear panel of the
UltraLine II to the Ethernet port on your computer. Repeat this step to connect up to three additional PCs to the
Modem.
Modem.
NOTE: You may connect to any of the four Ethernet jacks on the rear panel of the UltraLine II because they
serve as an Ethernet switch.
serve as an Ethernet switch.
3. Connect the power supply cord to the power connector marked 12 VDC on the rear panel of the UltraLine II.
Plug the other end of the power supply into a wall socket, and then turn on the power switch (if it is not already
turned on). Check to see if the Modem’s Wireless LED is solid green. This means that the Wireless interface is
functioning properly.
turned on). Check to see if the Modem’s Wireless LED is solid green. This means that the Wireless interface is
functioning properly.
4. Check to see if the UltraLine’s POWER LED is solid green. This indicates that the UltraLine II is powered on.
5. Check to see if the UltraLine’s WAN LED is solid green. Solid green indicates that the WAN connection is
functioning properly.