Laird Controls North America Inc. 79546-91071 ユーザーズマニュアル
LRM and PA Radio Module
CATTRON Engineering Group
Document p/n: 9S02-7954-A001 Rev.A
Cattron-Theimeg Inc.
Proprietary and Confidential
Page iv
79546+91071 TRX module meets Part 90 of the FCC rules and regulations. Compliance with the
labeling requirements, FCC notices is required. In order to comply with FCC Certification
requirements, the Original Equipment Manufacturer (OEM) must fulfill the following requirements.
labeling requirements, FCC notices is required. In order to comply with FCC Certification
requirements, the Original Equipment Manufacturer (OEM) must fulfill the following requirements.
1. The system integrator must place an exterior label on the outside of the final product
housing the 79546+91071TRX Module. The figure below shows the contents that must be
included in this label.
included in this label.
2. 79546+91071 TRX modules may only be used with the antennas that have been
tested and approved for use with the module.
Labeling Requirements
The OEM must make sure that FCC labeling requirements are met. This includes a clearly visible
exterior label on the outside of the final product housing that displays the contents shown in
below.
exterior label on the outside of the final product housing that displays the contents shown in
below.
WARNING: The 79546+91071 TRX modules have been tested by the FCC for use with other products
without further certification (as per FCC Section 2.1091). Changes or modifications to this device not
expressly approved by Cattron-Theimeg could void the user’s authority to operate the equipment.
without further certification (as per FCC Section 2.1091). Changes or modifications to this device not
expressly approved by Cattron-Theimeg could void the user’s authority to operate the equipment.
NOTICE: OEM’s must verify the final end product complies with unintentional radiators (FCC Section
15.107 and 15.109) before providing a declaration of conformity for their final product to Part 15 of the
FCC Rules.
15.107 and 15.109) before providing a declaration of conformity for their final product to Part 15 of the
FCC Rules.
NOTICE: The 79546+91071 TRX modules have been certified for mobile and fixed radio
applications. If the module will be used for portable applications, the device must undergo SAR
testing.
applications. If the module will be used for portable applications, the device must undergo SAR
testing.
RF Exposure WARNING: This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum distance 20
cm between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
uncontrolled environment. This equipment should be installed and operated with minimum distance 20
cm between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
NOTICE: The preceding statement must be included as a CAUTION statement in OEM product
manuals in order to alert users of FCC RF Exposure compliance.
79546+91071 TRX is designed for use in countless wireless applications requiring long range
communications with low energy consumption. To ensure that the final product complies with the all of
the regulatory requirements for the Modular Grant the following integration instructions should be
followed. 79546+91071 TRX is limited to OEM installation ONLY. The OEM integrator is responsible
for ensuring that the end-user has no manual instructions to remove or install the module.
manuals in order to alert users of FCC RF Exposure compliance.
79546+91071 TRX is designed for use in countless wireless applications requiring long range
communications with low energy consumption. To ensure that the final product complies with the all of
the regulatory requirements for the Modular Grant the following integration instructions should be
followed. 79546+91071 TRX is limited to OEM installation ONLY. The OEM integrator is responsible
for ensuring that the end-user has no manual instructions to remove or install the module.