Tecom Co Ltd GCDBC1 ユーザーズマニュアル
RED WIRE
BLACK WIRE
DIODE
16 VAC TRANSFORMER
BLACK WIRE: TRANSFORMER WIRE
RED WIRE: CATHODE OF DIODE
SMART
DOORBELL
CAMERA
PRINTER’S INSTRUCTIONS:
GUIDE, INSTALL, QUICK,GC-DBC-1- P/N 10010716 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 17.000” X 11.000” - TOLERANCE: ± .125” - SCALE: 1-1 -FOLDING, FOLD 3 X TO FINAL SIZE 4.250” X 5.625” FINISH WITH LOGO SHOWING - SIDE 1 OF 2
GC-DBC-1
Installation Instructions
System Description
SMART
DOORBELL
CAMERA
DOORBELL
TRANSFORMER
CHIME BOX
WiFi ROUTER
WiFi COMMUNICATIONS
CLOUD
SMARTPHONE
Doorbell Camera Components
POWER DRILL WITH 1/4” BIT
WIRE STRIPPERS / CUTTER
PHILLIPS SCREWDRIVER
LEVEL
0-M
0.5
10
50
200
500
50
250
10
50 250
600
+
-
AC VOLT METER
FLAT SCREWDRIVER
OPTIONAL
PLIERS
Tools For Installation
DIODES FOR
CHIME BOX (2)
USE LEVELING TOOL
TO ALIGN CAMERA
WITH LINE ON
MOUNTING PLATE
WIRE
CONNECTORS (4)
TORX
WRENCH
TORX SCREW
SMART
DOORBELL
CAMERA
SMART DOORBELL
CAMERA MOUNTING
PLATE
PHILLIPS SCREWS
(3)
(3)
ANCHORS
(3)
(3)
SMARTPHONE
EXISTING
DOORBELL
Prepare for Installation
• Go to existing doorbell location.
• Use a Smartphone connected to the installations WiFi
• Use a Smartphone connected to the installations WiFi
router to confi rm adequate signal strength (2 - 3 bars).
Existing Doorbell Removal
DISCONNECT WIRES
FROM PUSHBUTTON
FROM PUSHBUTTON
DOORBELL
• Remove existing doorbell pushbutton from location.
• Disconnect wires from back of pushbutton.
• Disconnect wires from back of pushbutton.
Measure Voltage
0-M
0.5
10
50
200
500
50
250
10
50 250
600
+
-
TEST VOLTAGE
OF WIRES
(REQUIRES
15 TO 20 VAC)
• Measure voltage of doorbell wiring with AC Volt
Meter.
• Doorbell camera works best with 15 to 20 VAC.
Mounting Doorbell Camera Plate
UP
OR
UP
UP
USE 1/4" (6.35mm) DRILL FOR
ANCHOR HOLES
SCREWS ONLY
SCREWS & ANCHORS
• Use mounting plate as guide to mark holes.
Wiring Doorbell Camera
1.
TWIST THEN
FEED WIRES INTO
SHORT END OF
CONNECTOR
SHORT END OF
CONNECTOR
2
.
CRIMP WIRES
WITH PLIERS ON
SHORT END OF
CONNECTOR
SHORT END OF
CONNECTOR
CONNECTORS
IN PLACE
• Connect doorbell wires using weather-
resistant wire connectors (included).
System Overview
BLACK WIRE: TRANSFORMER WIRE
RED WIRE: CHIME BOX WIRE
CHIME BOX
16 VAC TRANSFORMER
REAR
TRANS
FRONT
REAR
TRANS
FRONT
1
OPEN CHIME BOX
CHIME BOX FRONT VIEW WITHOUT COVER
2
INSTALL DIODE AS SHOWN
DIODE
(CATHODE
ON FRONT
TERMINAL)
(CATHODE
ON FRONT
TERMINAL)
IMPORTANT STEP
Installing Diode in Chime Box
1
2
3
4
5
6
7
Wiring Camera WITHOUT Chime
✔ NOTE: Not compatible with electronic chimes
✔ NOTE: It is recommended to TURN POWER OFF
after verifying voltage.
(OPTIONAL)