Computime Limited RCM-RX ユーザーズマニュアル
RCTE
Thermostatic On/Off Remote Control – 110VAC
INSTALLATION AND OPERATING INSTRUCTIONS
This thermostatic 110 VAC on/off remote control system provides
a safe, reliable, and user-friendly remote control for millivolt
valve gas appliances. The system can be operated in a thermostat-
ically or manual mode. Always check the appliance home
owner’s manual for additional information, or warnings regarding
accessory installation before connecting this remote control sys-
tem.
Carefully inspect the contents for shipping damage. If any parts
are missing or damaged, immediately contact the dealer from
whom you purchased the kit. Do not attempt to install any part of
the kit unless all parts are in good condition. Please keep this
booklet for future reference.
CONTENTS OF KIT
Description
Qty
Transmitter
1
Battery Alkaline AAA ( for Transmitter)
3
Receiver (Assembly) consists of:
1
Receiver Box with 110 VAC Adapter
Slide Button-Black (On/RS/Off)
L-Bracket (Floor Mount)
Wall Cover Plate-Black
1
Wall Cover Plate-White
1
Slide Button-White (On/RS/Off)
1
Screws (for Wall Cover Plate)
2
Plug-In Wiring Assembly – 18" Inches
1
Velcro (Loop and Hook)
1
Wall Holster
1
Wall Holster Screws
2
Wall Anchor
2
Screws (for fireplace system control covers)
2
Installation Instructions
1
FEATURES/SPECIFICATIONS
•
Contemporary Ergonomic Style Transmitter with Large LCD
Display
•
Backlit LCD Display
•
Battery Powered Transmitter
•
Compact 110 VAC Adapter with 30" wire
•
Pre-Programmed for Quick Installation
•
Low battery Indication
•
Child Proof Lock-out
•
128 Security Codes
•
Quick Disconnect Wiring Assembly
•
On/Off, Thermostatic, Timer, and 5-2 Day Thermostatic
Programming Flexibility
•
Reset Button
WARNING
Important Safety Information
•
Read this manual thoroughly prior to installing, programming
or operating any remote control.
•
This remote control system is designed for use with a
millivolt gas valve system. Do not use this remote control
system on applications with voltages above 30 Volts AC.
•
This remote control system requires three (3) "AAA" batteries
to power the transmitter and 110 VAC to power the receiver.
Wiring must conform to appliance requirement and building
codes/ordinances as required by local and national code
authorities having jurisdiction.
•
Do not short (or jumper) across the gas valve terminals to test
the remote control installation. This could damage the unit
and void the warranty.
•
This remote control system should only be used as described
in this manual. Any other use is not recommended and will
void the warranty.
Due to the sensitive temperature monitoring
components in the transmitter, it is necessary to
allow the transmitter to stabilize to room
temperature before accurate room temperatures
are displayed. If the transmitter is activated from
a severe cold condition, allow 15 minutes for
accurate temperature readings to appear on the
LCD.
Turn appliance OFF and allow to cool before
installing or servicing. DO NOT connect
110-120 VAC wiring to the milli-volt gas control
valve. The remote operator must be installed
exactly as outlined in these instructions. Read all
instructions completely before attempting
installation. Follow instructions carefully during
installation. Any modification of components will
void the warranty and may cause a fire hazard.
Low battery power in the transmitter or receiver
can affect the operation of the remote control in
the AUTO mode. In some cases the unit may not
cycle off when the target temperature is reached.
INSTALLATIONS
Remote Receiver:
The remote receiver may be wall mounted or installed into the
appliance per the appliance homeowner’s manual. Refer to the
Homeowner’s Manual for special installation instructions. If
wall mounted, the remote receiver must be installed in a junction
box with cover plate provided. Failure to follow the installation
instructions found in the appropriate Homeowner’s Manual will
void the warranty and may cause a fire hazard.
Power up Receiver:
The receiver is powered by plugging into a polarized 110VAC out-
let.
Installing Wire:
This system comes with an 18 inch pre-assembled wire assembly.
Insert the white terminal to the back of the receiver. The terminal
wire block can only be installed one way. Do not force the termi-
nal plug onto the receiver.
Follow the homeowner’s manual for connecting the two (2) 1/4"
female spade terminals to the millivolt valve.
For applications longer than 18 inches, use 18 gauge wire or larg-
er, 105ºC rated, with as few splices as possible. Connect to the
two (2) 1/4" female spade wiring terminals. Wire can be no
longer than 20 feet.
Make sure that the wires do not contact the
appliances any place other than at the terminals.
Exposure to temperatures higher than 105C
(250ºF) may cause the receiver to malfunction or
fire hazard.
Remote Transmitter:
Installing Batteries:
The remote transmitter uses three
(3) "AAA"- size batteries. To
install batteries,
1.Press down the battery door tab
and lift up and remove the battery
door.
2.Install the batteries as indicated in
the receiver cover.
3.Close the battery door by
snapping in place.
4.The batteries should be replaced
at least once every 6 months or
when the battery indicator flashes.
Setting Privacy (DIP) Switch on Receiver and Transmitter:
The remote receiver and transmitter privacy (DIP) switches are
preset at the factory. Do not set all DIP switches to "OFF" posi-
tion or "ON" position. The receiver and transmitter privacy (DIP)
swithes are preset at the factory. In the event of activation or
interference from other nearby transmissions, reset the code using
the following procedure:
1.Slide the code switches on the transmitter or receiver to your
choice of ON or OFF position. Switches #1 to #6 are preset to
"ON", and #7 is preset to "OFF" on both the transmitter and
receiver.
2.The switches on the transmitter and receiver must match in
order for the system to work.
3. The system is now ready to operate.
Do not use two (2) or more remote control systems
in the same area with the same dip switch settings,
as they will communicate with each other. This
may cause the appliances to malfunction.
Reset Button:
1.The reset button can be used to reset the systems such as the
clock setting. The reset button is located behind the battery
door cover.
2.Using a paper clip, press the button and the system will reset
and go into clock setting mode. Follow the instructions on how
to set the time in the next section.
Installing Wall Holster:
The transmitter wall holster can be attached to any wall. Use the
wall anchors and screws to secure the wall holster.
OPERATIONS:
Transmitter:
General:
The RCTE Remote Control has four (4 ) operat-
ing modes: Manual, Timer, Auto, and Auto-P.
The control system can be set to temperature
ranges between 45
∞F and 90∞F.
The transmitter will operate the remote receiver
from 1foot to a maximum of 30 feet. The dis-
tance is reduced when batteries are low or when
the receiver is inside a metal enclosure.
Initial start up:
1.After initial power up or when RESET button is pressed, the
transmitter is reset. The reset button is located inside the battery
door.
2.During system reset, all features of the LCD will be visible.
After one second, the LCD will be initialized. A typical reset
display is shown above. Note that the temperature scale is
degree F.
3.While
∞F is flashing, press and hold SET and TIME/CANCEL
for more than 3 seconds to select between
∞C and ∞F display. It
will exit setting mode automatically after 10 seconds if no key is
pressed.
4.After reset the transmitter is operating in manual mode. The
time and room temperature are shown as above.
Setting Clock:
1.While in Manual mode, press SET to enter clock setting mode.
2.In clock setting mode, only clock is displayed. Press SET to
select item (hour, minute or day). Selected item is flashing.
Press 4 or 3 to change. Selected item is flashing.
Manual Mode:
1.Press the ON button once to turn on the appliance. Press the
OFF button to turn it off.
2.In manual mode, the transmitter will not turn the appliance off
even if the room temperature is above the target temperature.
Timer mode:
1.In manual or auto mode press TIME/CANCEL to enter Timer
mode. LCD will display only the timer time and room
temperature.
2.In Timer mode, the preset time is 120 minutes (maximum).
3.Press 4 or 3 to change timer time in 10 minute increments.
4.The transmitter will turn on the appliance when entering timer
mode. When the times run out, the transmitter will turn off the
appliance and return to Manual mode.
W
A
R
N
IN
G
W
A
R
N
IN
G
N
O
T
E
W
A
R
N
IN
G
Adapter plug to 110VAC outlet or built in
junction box in the appliance
junction box in the appliance
Plug In For 18" wire assembly
Remote Receiver
30" Adapter Wire
Back of the Transmitter
Battery
Door
Tab
Receiver
Transmitter
W
A
R
N
IN
G
RCM-RX