Computime Limited RCT ユーザーズマニュアル

Timer mode:

1.In manual or auto mode press TIME/CANCEL to enter Timer 

mode. LCD will display only the timer time and room 

temperature.
2. In Timer mode, the preset time and temperature is 120 minutes 

(maximum) and 70 degrees Fahrenheit (room temperature).

3. Press 

4

or 

3

to select timer time in 10 minute increments.  

Press SET and 

4

or 

3

to set temperature.

4. The transmitter will turn on the appliance when entering timer 

mode.  When the times run out, the transmitter will turn off the 
appliance and return to Manual mode.

5. Timer count down can be cancelled by pressing:

a. TIME/CANCEL which returns back to previous mode
b. ON  or OFF which returns to manual mode,
c. AUTO which then goes to auto mode.

Auto mode:

1. To enter auto mode, press AUTO in manual mode or timer 

mode. 

2. In auto mode, press SET and press 

4

, 

3

to set temperature.

3. After entering auto mode, once the setting is completed, the 

transmitter will automatically turn on the fireplace when the 
room temperature is below the target temperature and turn off 
the appliance when the room temperature is above the target 
temperature.

4. There will be a slight delay in the response of the unit (on/off) 

to a temperature.  Temperature is monitored every 3 minutes.

5. Flame icon will display when the transmitter is in "ON".
6. Pressing either the ON or OFF button, it will change to Manual 

mode.

7. When AUTO and ON buttons are pressed simultaneously and 

held more than 3 seconds, it will enter Auto-P (program) mode.

8. When TIMER/CANCEL button is pressed, it will change to 

timer mode.

Auto-P mode:

1. To enter Auto-P mode, press AUTO and ON buttons and hold 

more than 3 seconds.  Press AUTO again. 

2. When entering Auto-P mode, there are no default values and a 

blank display will be seen as illustrated below.

3. In this display, press 

4

or 

3

buttons to enter information, 

LCD will be display as shown below.  When entering Program 
setting mode for the first time, program 1 for the first day will 
display as shown below. 6am is flashing to indicate the selected 
item to be adjusted.

4. Use AUTO to select among the items of the day shown: hour, 

minute and temperature of program 1. Subsequence presses will 
proceed to program 2, 3 and 4 and then repeat again.

5. Selected item will be flashing and can be adjusted by 

4

or

3

key.  Program time is changed in 10 minute increment. Setting 
range in Fahrenheit mode is 45-90°F in step of 1°F. The setting 
range in Celsius mode is 7-32°C in step of 1°C.

6. Once the settings are complete and/or no keys are pressed with-

in 10 seconds, the program will function.

7. The transmitter will automatically turn on the fireplace when the

room temperature is below the target temperature and turn off 
the appliance when the room temperature is above the target 
temperature.

8. There will be a slight delay in the response of the unit (on/off) 

to a temperature change.Temperature is monitored every 3
minutes

9. When ON or OFF buttons are pressed, it will change to Manual 

mode.

10. When AUTO button is pressed, it will change to Auto mode.
11. When TIMER/CANCEL button is pressed, it will change 

timer mode.

Low-battery detection:

1. Battery voltage is checked once a minute. When the battery 

voltage drops to a certain level, the low-battery warning will 
come on, and the transmitter will turn off the appliance.  The 
transmitter will not function anymore until fresh batteries are 
installed.

2. When the batteries are low, the LCD shows a low battery 

indicator. The low battery warning will be displayed in any 
mode.

3. The transmitter will not operate with low batteries.   Change the 

battery before the battery is too weak for normal operation.  
TURN THE UNIT OFF BEFORE REPLACING 

BATTERIES.

Child-proof protection:

1. Press and hold ON and OFF buttons simultaneously for 3 

seconds to enter child-proof mode.

2. The transmitter will not work mode until child-proof mode is 

deactivated by pressing the ON and OFF buttons simultaneously
for 3 seconds again to exit child-proof mode.

Transmitter Thermal Shutdown:

1. If transmitter measures a room temperature exceeding 99 

degrees Fahrenheit, the LCD will display "HI" and the 

transmitter will turn off the appliance.
2. Transmitter will not function until the room temperature has 

dropped below 99 degree Fahrenheit.

Slide Switch:

1. ON position: the system will remain on until the slide switch is 

placed in the OFF or RS position.

2. RS position: the system will only operate if the remote receiver 

receives a signal from the transmitter.

3. OFF position, the system is off.  The slide switch should be 

placed in the OFF position if you will be away for an extended 
period of time.   If the remote receiver is mounted out of 
children’s reach, the OFF position also functions as a safety 
device by both turning the system off and rendering the receiver 
inoperable.

1. Connect the wiring terminal to the appliance.  Refer to the 

appropriate Homeowner’s Manual for proper wiring connections
to the appliance.

2. Light your gas appliance following the appliance lighting 

instructions that came with the appliance.  Confirm that the pilot
light is on;  it must be in operation for the remote control to 
operate the main gas valve.  Appliance control knob must be in 
the ON position.  Appliance ON/OFF switch must be in OFF 
position.

3. Slide the 3 position button on the remote receiver to the ON 

position.  The main gas flame should ignite.

4. Slide the button to OFF.   The flame should extinguish (the pilot

light will remain on).

5. Slide the button to RS (the center position), then press the ON 

button on the transmitter to turn the system to ON.  The main 
gas flame should ignite. 

6. Press the OFF button on the transmitter to turn the system to 

OFF.  The flame should extinguish (the pilot light will remain 
on).

WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.  These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instruc-
tions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a
particular installation.   If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following meas-
ures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for 

help.

This warranty gives you specific legal rights and you may also

have other rights that vary from state to state or province to

province.  Answers to any questions regarding our limited warran-

ty may be obtained by writing our corporate offices.

Ambient Technologies warrants each new Ambient Technologies

remote control against any defects that are due to faulty material

or workmanship to the original owner, for a period of five years

after the original date of purchase.  This warranty and our liability

does not apply to batteries, nor does it include damage to mer-

chandise or the remote control resulting from accident, alteration,

neglect, misuse, improper installation or any other failure to fol-

low Ambient Technologies installation and operating instructions.

Ambient Technologies agrees to repair or replace at its option any

Ambient Technologies remote control under warranty provided it

is returned postage prepaid to our warranty facility in a padded

carton within the warranty period, with proof of the original date

of purchase and a brief description of the malfunction.  This limit-

ed warranty does not include the cost of removal or re-installation.

Ambient Technologies

FOR

TECHNICAL SUPPORT

149 Cleveland Drive

CALL

800-398-6195

Paris KY 40361

Symptom

1. LED light on receiver 

blinking or battery icon 
on LCD on transmitter.

2. LCD display is blank
3. LCD display shows 

"funny" display

4. Appliance does not come

on after pressing ON on 
transmitter

5. Receiver cannot receive 

signal.

Causes

1. Low Battery 

1. Wiring / Electrical 

Connections

2. Privacy (DIP) switch 

setting on transmitter
does not match 
receiver

3. Transmitter measures

temperature 
exceeding 99 degrees
Fahrenheit  and 
shows "HI" on LCD

4. Distance between the

transmitter and 
receiver is more than 
30 feet

1. Receiver is installed 

in an enclosure

Action

1. Replace batteries. Change

batteries every 6 months.

2. Check battery installation 

and replace batteries.

3. Press Reset button at the 

back of the transmitter.  
The reset button is located
at the lower left corner 
behind the battery cover.

1. Slide the switch to ON, if 

appliance comes ON, 
wiring is not the causes.

2. If appliance does not 

come on, check wiring 
connections.

1. Make sure the transmitter 

and receiver has the same 
DIP switch settings.

1. Move transmitter to a 

cooler place and wait 
until temperature drops 
below 99 degree.

1. Make sure the operating 

distance is less than 30 
feet

1. Make sure the receiver is 

not located inside an 
enclosure.